P89LPC982FDH,529 NXP Semiconductors, P89LPC982FDH,529 Datasheet - Page 43

• Manufacturer Part Number: P89LPC982FDH,529
• Description: MCU 80C51 8KB FLASH 28TSSOP
• Manufacturer: NXP Semiconductors
• Series: LPC900r

Specifications of P89LPC982FDH,529

• Program Memory Type: FLASH
• Program Memory Size: 8KB (8K x 8)
• Package / Case: 28-TSSOP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 18MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 26
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: P89LPC
• Core: 80C51
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 18 MHz
• Number Of Programmable I/os: 23
• Number Of Timers: 5
• Operating Supply Voltage: 2.4 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 935290303529

NXP Semiconductors
P89LPC980_982_983_985
Product data sheet
7.18.1 Reset vector
7.18 Reset
or not. When switching back to high speed mode, first clear LPMOD bit to select high
speed mode, then check HCOK bit. If HCOK bit turns to ‘1’, it means the switch was
completed.
The P1.5/RST pin can function as either a LOW-active reset input or as a digital input,
P1.5. The Reset Pin Enable (RPE) bit in UCFG1, when set to logic 1, enables the external
reset input function on P1.5. When cleared, P1.5 may be used as an input pin.
Remark: During a power-up sequence, the RPE selection is overridden and this pin
always functions as a reset input. An external circuit connected to this pin should not
hold this pin LOW during a power-on sequence as this will keep the device in reset.
After power-up this pin will function as defined by the RPE bit. Only a power-up reset will
temporarily override the selection defined by RPE bit. Other sources of reset will not
override the RPE bit.
Reset can be triggered from the following sources:
For every reset source, there is a flag in the Reset Register, RSTSRC. The user can read
this register to determine the most recent reset source. These flag bits can be cleared in
software by writing a logic 0 to the corresponding bit. More than one flag bit may be set:
Following reset, the P89LPC980/982/983/985 will fetch instructions from either address
0000H or the Boot address. The Boot address is formed by using the boot vector as the
high byte of the address and the low byte of the address = 00H.
The boot address will be used if a UART break reset occurs, or the non-volatile boot
status bit (BOOTSTAT.0) = 1, or the device is forced into ISP mode during power-on (see
P89LPC980/982/983/985 User manual). Otherwise, instructions will be fetched from
address 0000H.
•
•
•
•
•
•
•
•
•
External reset pin (during power-up or if user configured via UCFG1)
Power-on detect
Brownout detect
Watchdog timer
Software reset
UART break character detect reset
During a power-on reset, both POF and BOF are set but the other flag bits are
cleared.
A watchdog reset is similar to a power-on reset, both POF and BOF are set but the
other flag bits are cleared.
For any other reset, previously set flag bits that have not been cleared will remain set.
Rev. 4 — 15 June 2010
8-bit microcontroller with accelerated two-clock 80C51 core
P89LPC980/982/983/985
© NXP B.V. 2010. All rights reserved.
43 of 85