M3062GF8NGP#U5 Renesas Electronics America, M3062GF8NGP#U5 Datasheet - Page 163

• Manufacturer Part Number: M3062GF8NGP#U5
• Description: MCU 3V 64K PB FREE 100-LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/60r

Specifications of M3062GF8NGP#U5

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 10MHz
• Connectivity: SIO, UART/USART
• Peripherals: DMA, WDT
• Number Of I /o: 85
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 10x10b, D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 100-LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

Programmable I/O Port
160
Rev.1.1
Programmable I/O Ports
There are 87 programmable I/O ports: P0 to P10 (excluding P8
input or output using the direction register. A pull-up resistance for each block of 4 ports can be set. P8
an input-only port and has no built-in pull-up resistance.
Figures 1.20.1 to 1.20.4 show the programmable I/O ports. Figure 1.20.5 shows the I/O pins.
Each pin functions as a programmable I/O port and as the I/O for the built-in peripheral devices.
To use the pins as the inputs for the built-in peripheral devices, set the direction register of each pin to input
mode. When the pins are used as the outputs for the built-in peripheral devices (other than the D-A con-
verter), they function as outputs regardless of the contents of the direction registers. When pins are to be
used as the outputs for the D-A converter, do not set the direction registers to output mode. See the
descriptions of the respective functions for how to set up the built-in peripheral devices.
(1) Direction registers
(2) Port registers
(3) Pull-up control registers
(4) Port control register
Figure 1.20.6 shows the direction registers.
These registers are used to choose the direction of the programmable I/O ports. Each bit in these regis-
ters corresponds one for one to each I/O pin.
In memory expansion and microprocessor mode, the contents of corresponding direction register of pins
A
be modified.
Note: There is no direction register bit for P8
Figure 1.20.7 shows the port registers.
These registers are used to write and read data for input and output to and from an external device. A
port register consists of a port latch to hold output data and a circuit to read the status of a pin. Each bit
in port registers corresponds one for one to each I/O pin.
In memory expansion and microprocessor mode, the contents of corresponding port register of pins A
A
modified.
Figure 1.20.8 shows the pull-up control registers.
The pull-up control register can be set to apply a pull-up resistance to each block of 4 ports. When ports
are set to have a pull-up resistance, the pull-up resistance is connected only when the direction register is
set for input.
However, in memory expansion mode and microprocessor mode, the pull-up control register of P0 to P3,
P4
connected.
Figure 1.20.9 shows the port control register.
The bit 0 of port control register is used to read port P1 as follows:
This register is valid in the following:
0
19
0
to A
0 : When port P1 is input port, port input level is read.
1 : The contents of port P1 register is read always.
• External bus width is 8 bits in microprocessor mode or memory expansion mode.
• Port P1 can be used as a port in multiplexed bus for the entire space.
, D
to P4
0
When port P1 is output port , the contents of port P1 register is read.
19
to D
, D
3
, and P5 is invalid. The contents of register can be changed, but the pull-up resistance is not
0
15
to D
, CS0 to CS3, RD, WRL/WR, WRH/BHE, ALE, RDY, HOLD, HLDA and BCLK cannot be
_______
15
, CS0 to CS3, RD, WRL/WR, WRH/BHE, ALE, RDY, HOLD, HLDA and BCLK cannot
_______
________ _____
_______
________ ______
_____
________ ______
5
________ ________
.
________ _______
5
_______
). Each port can be set independently for
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
_______
__________
__________
_________
_________
M3062GF8NFP/GP
Mitsubishi microcomputers
0
5
to
is