HD64F3067RF20 Renesas Electronics America, HD64F3067RF20 Datasheet - Page 578

• Manufacturer Part Number: HD64F3067RF20
• Description: IC H8 MCU FLASH 128K 100-QFP
• Manufacturer: Renesas Electronics America
• Series: H8® H8/300Hr

Specifications of HD64F3067RF20

• Core Processor: H8/300H
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: SCI, SmartCard
• Peripherals: DMA, PWM, WDT
• Number Of I /o: 70
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 8x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 75°C
• Package / Case: 100-QFP
• Package: 100PQFP
• Family Name: H8
• Maximum Speed: 20 MHz
• Operating Supply Voltage: 5 V
• Data Bus Width: 16|32 Bit
• Number Of Programmable I/os: 70
• Interface Type: SCI
• On-chip Adc: 8-chx10-bit
• On-chip Dac: 2-chx8-bit
• Number Of Timers: 7
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

Section 14 Smart Card Interface
5. If the transmitting device does not receive an error signal, it proceeds to transmit the next data
14.3.4
Table 14.3 shows a bit map of the registers used in the smart card interface. Bits indicated as 0 or
1 must be set to the value shown. The setting of other bits is described in this section.
Table 14.3 Smart Card Interface Register Settings
Register Address *
SMR
BRR
SCR
TDR
SSR
RDR
SCMR
Notes: — Unused bit.
Serial Mode Register (SMR) Settings: Clear the GM bit to 0 when using the normal smart card
interface mode, or set to 1 when using GSM mode. Clear the O/E bit to 0 if the smart card is of the
direct convention type, or set to 1 if of the inverse convention type.
Bits CKS1 and CKS0 select the clock source of the built-in baud rate generator. See section
14.3.5, Clock.
Bit Rate Register (BRR) Settings: BRR is used to set the bit rate. See section 14.3.5, Clock, for
the method of calculating the value to be set.
Serial Control Register (SCR) Settings: The TIE, RIE, TE, and RE bits have their normal serial
communication functions. See section 13, Serial Communication Interface, for details. The CKE1
and CKE0 bits specify clock output. To disable clock output, clear these bits to 00; to enable clock
Rev. 4.00 Jan 26, 2006 page 554 of 938
REJ09B0276-0400
the receiving device places the signal line in the high-impedance state again. The signal line is
pulled high again by a pull-up resistor.
frame. If it receives an error signal, however, it returns to step 2 and transmits the same data
again.
1. Lower 20 bits of the address in advanced mode.
2. When GM is cleared to 0 in SMR, the CKE1 bit must also be cleared to 0.
Register Settings
H'FFFB0
H'FFFB1
H'FFFB2
H'FFFB3
H'FFFB4
H'FFFB5
H'FFFB6
1
Bit 7
GM
BRR7
TIE
TDR7
TDRE
RDR7
—
Bit 6
0
BRR6
RIE
TDR6
RDRF
RDR6
—
Bit 5
1
BRR5
TE
TDR5
ORER
RDR5
—
BRR4
TDR4
RDR4
Bit 4
O/E
RE
ERS
—
Bit
Bit 3
1
BRR3
0
TDR3
PER
RDR3
SDIR
Bit 2
0
BRR2
0
TDR2
TEND
RDR2
SINV
Bit 1
CKS1
BRR1
CKE1 *
TDR1
0
RDR1
—
2
Bit 0
CKS0
BRR0
CKE0
TDR0
0
RDR0
SMIF