AT91SAM7SE256B-CUR Atmel, AT91SAM7SE256B-CUR Datasheet - Page 506

• Manufacturer Part Number: AT91SAM7SE256B-CUR
• Description: IC ARM7 MCU FLASH 256K 128-LQFP
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7SE256B-CUR

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 55MHz
• Connectivity: EBI/EMI, I²C, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 88
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Processor Series: SAM7SE256
• Core: ARM7TDMI
• Data Bus Width: 32 bit
• Data Ram Size: 32 KB
• Interface Type: SPI, USB
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 88
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Operating Temperature Range: - 40 C to + 85 C
• Processor To Be Evaluated: AT91SAM7SE256B
• Supply Current (max): 60 uA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

36.5.1.3
36.5.1.4
36.5.1.5
506
SAM7SE512/256/32 Preliminary
Clock Control
TC Operating Modes
Trigger
The clock of each counter can be controlled in two different ways: it can be enabled/disabled
and started/stopped. See
Figure 36-4. Clock Control
Each channel can independently operate in two different modes:
The TC Operating Mode is programmed with the WAVE bit in the TC Channel Mode Register.
In Capture Mode, TIOA and TIOB are configured as inputs.
In Waveform Mode, TIOA is always configured to be an output and TIOB is an output if it is not
selected to be the external trigger.
A trigger resets the counter and starts the counter clock. Three types of triggers are common to
both modes, and a fourth external trigger is available to each mode.
The following triggers are common to both modes:
• The clock can be enabled or disabled by the user with the CLKEN and the CLKDIS
• The clock can also be started or stopped: a trigger (software, synchro, external or compare)
• Capture Mode provides measurement on signals.
• Waveform Mode provides wave generation.
commands in the Control Register. In Capture Mode it can be disabled by an RB load event if
LDBDIS is set to 1 in TC_CMR. In Waveform Mode, it can be disabled by an RC Compare
event if CPCDIS is set to 1 in TC_CMR. When disabled, the start or the stop actions have no
effect: only a CLKEN command in the Control Register can re-enable the clock. When the
clock is enabled, the CLKSTA bit is set in the Status Register.
always starts the clock. The clock can be stopped by an RB load event in Capture Mode
(LDBSTOP = 1 in TC_CMR) or a RC compare event in Waveform Mode (CPCSTOP = 1 in
TC_CMR). The start and the stop commands have effect only if the clock is enabled.
Selected
Counter
Clock
Clock
Figure
Q
36-4.
R
S
Trigger
CLKSTA
Q
CLKEN
S
R
Event
Stop
CLKDIS
Disable
Event
6222F–ATARM–14-Jan-11