LFXP2-17E-5FN484I Lattice, LFXP2-17E-5FN484I Datasheet - Page 89

• Manufacturer Part Number: LFXP2-17E-5FN484I
• Description: FPGA - Field Programmable Gate Array 17K LUTs 358 I/O Ins on DSP 1.2V -5 Spd
• Manufacturer: Lattice

Specifications of LFXP2-17E-5FN484I

• Number Of Macrocells: 17000
• Number Of Programmable I/os: 358
• Data Ram Size: 282624
• Supply Voltage (max): 1.26 V
• Maximum Operating Temperature: + 100 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Supply Voltage (min): 1.14 V
• Package / Case: FPBGA-484
• Number Of Logic Elements/cells: *
• Number Of Labs/clbs: *
• Total Ram Bits: 282624
• Number Of I /o: 358
• Number Of Gates: -
• Voltage - Supply: 1.14 V ~ 1.26 V
• Mounting Type: *
• Operating Temperature: -40°C ~ 100°C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Signal Descriptions
June 2008
© 2008 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand
or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
www.latticesemi.com
General Purpose
P[Edge] [Row/Column Number*]_[A/B]
GSRN
NC
GND
V
V
V
V
V
PLL and Clock Functions (Used as user programmable I/O pins when not in use for PLL or clock pins)
[LOC][num]_V
[LOC][num]_GPLL[T, C]_IN_A
[LOC][num]_GPLL[T, C]_FB_A
PCLK[T, C]_[n:0]_[3:0]
[LOC]DQS[num]
Test and Programming (Dedicated Pins)
TMS
TCK
TDI
CC
CCAUX
CCPLL
CCIOx
REF1_x
, V
REF2_x
Signal Name
CCPLL
I/O
I/O
—
—
—
—
—
—
—
—
I
I
I
I
I
I
I
I
[Edge] indicates the edge of the device on which the pad is located. Valid
edge designations are L (Left), B (Bottom), R (Right), T (Top).
[Row/Column Number] indicates the PFU row or the column of the device on
which the PIC exists. When Edge is T (Top) or B (Bottom), only need to spec-
ify Row Number. When Edge is L (Left) or R (Right), only need to specify Col-
umn Number.
[A/B] indicates the PIO within the PIC to which the pad is connected. Some of
these user-programmable pins are shared with special function pins. These
pins, when not used as special purpose pins, can be programmed as I/Os for
user logic. During configuration the user-programmable I/Os are tri-stated
with an internal pull-up resistor enabled. If any pin is not used (or not bonded
to a package pin), it is also tri-stated with an internal pull-up resistor enabled
after configuration.
Global RESET signal (active low). Any I/O pin can be GSRN.
No connect.
Ground. Dedicated pins.
Power supply pins for core logic. Dedicated pins.
Auxiliary power supply pin. This dedicated pin powers all the differential and
referenced input buffers.
PLL supply pins. csBGA, PQFP and TQFP packages only.
Dedicated power supply pins for I/O bank x.
Reference supply pins for I/O bank x. Pre-determined pins in each bank are
assigned as V
Power supply pin for PLL: LLC, LRC, URC, ULC, num = row from center.
General Purpose PLL (GPLL) input pads: LLC, LRC, URC, ULC, num = row
from center, T = true and C = complement, index A,B,C...at each side.
Optional feedback GPLL input pads: LLC, LRC, URC, ULC, num = row from
center, T = true and C = complement, index A,B,C...at each side.
Primary Clock pads, T = true and C = complement, n per side, indexed by
bank and 0,1,2,3 within bank.
DQS input pads: T (Top), R (Right), B (Bottom), L (Left), DQS, num = ball
function number. Any pad can be configured to be output.
Test Mode Select input, used to control the 1149.1 state machine. Pull-up is
enabled during configuration.
Test Clock input pin, used to clock the 1149.1 state machine. No pull-up
enabled.
Test Data in pin. Used to load data into device using 1149.1 state machine.
After power-up, this TAP port can be activated for configuration by sending
appropriate command. (Note: once a configuration port is selected it is
locked. Another configuration port cannot be selected until the power-up
sequence). Pull-up is enabled during configuration.
LatticeXP2 Family Data Sheet
4-1
REF
inputs. When not used, they may be used as I/O pins.
Description
Pinout Information
Pinout Information_01.5
Data Sheet DS1009