ATmega64A Atmel Corporation, ATmega64A Datasheet - Page 61

• Manufacturer Part Number: ATmega64A
• Manufacturer: Atmel Corporation

Specifications of ATmega64A

• Flash (kbytes): 64 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 53
• Ext Interrupts: 8
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Uart: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 4
• Eeprom (bytes): 2048
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 8
• Input Capture Channels: 2
• Pwm Channels: 7
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

8160C–AVR–07/09
Table 11-1.
Notes:
Table 11-2
BOOTRST and IVSEL settings. If the program never enables an interrupt source, the Interrupt
Vectors are not used, and regular program code can be placed at these locations. This is also
the case if the Reset Vector is in the Application section while the Interrupt Vectors are in the
Boot section or vice versa.
Table 11-2.
Note:
The most typical and general program setup for the Reset and Interrupt Vector Addresses in
ATmega64A is:
Vector
BOOTRST
No.
Address Labels Code
0x0000
0x0002
0x0004
0x0006
0x0008
0x000A
0x000C
0x000E
0x0010
27
28
29
30
31
32
33
34
35
1
1
0
0
1. When the BOOTRST Fuse is programmed, the device will jump to the Boot Loader address at
2. When the IVSEL bit in MCUCR is set, Interrupt Vectors will be moved to the start of the Boot
3. The Interrupts on address 0x0030 - 0x0044 do not exist in ATmega103 compatibility mode.
1. The Boot Reset Address is shown in
reset, see
Flash section. The address of each Interrupt Vector will then be address in this table added to
the start address of the Boot Flash section.
means unprogrammed while “0” means programmed.
shows Reset and Interrupt Vectors placement for the various combinations of
Program
Address
0x003A
0x003C
0x003E
0x0034
0x0036
0x0038
0x0040
0x0042
0x0044
Reset and Interrupt Vectors (Continued)
Reset and Interrupt Vectors Placement
IVSEL
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
jmp
(2)
(3)
(3)
(3)
(3)
(3)
(3)
(3)
(3)
(3)
“Boot Loader Support – Read-While-Write Self-programming” on page
0
1
0
1
Source
TIMER3 COMPA
TIMER3 COMPB
TIMER3 COMPC
TIMER3 OVF
USART1, RX
USART1, UDRE
USART1, TX
TWI
SPM READY
Reset Address
0x0000
0x0000
Boot Reset Address
Boot Reset Address
RESET
EXT_INT0
EXT_INT1
EXT_INT2
EXT_INT3
EXT_INT4
EXT_INT5
EXT_INT6
EXT_INT7
; Reset Handler
; IRQ0 Handler
; IRQ1 Handler
; IRQ2 Handler
; IRQ3 Handler
; IRQ4 Handler
; IRQ5 Handler
; IRQ6 Handler
; IRQ7 Handler
Table 26-6 on page
Comments
Interrupt Definition
Timer/Counter3 Compare Match A
Timer/Counter3 Compare Match B
Timer/Counter3 Compare Match C
Timer/Counter3 Overflow
USART1, Rx Complete
USART1 Data Register Empty
USART1, Tx Complete
Two-wire Serial Interface
Store Program Memory Ready
(1)
Interrupt Vectors Start Address
0x0002
Boot Reset Address + 0x0002
0x0002
Boot Reset Address + 0x0002
292. For the BOOTRST Fuse “1”
ATmega64A
281.
61