SAM9G45 Atmel Corporation, SAM9G45 Datasheet - Page 554

• Manufacturer Part Number: SAM9G45
• Manufacturer: Atmel Corporation

Specifications of SAM9G45

• Flash (kbytes): 0 Kbytes
• Pin Count: 324
• Max. Operating Frequency: 400 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 160
• Ext Interrupts: 160
• Usb Transceiver: 3
• Usb Speed: Hi-Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 2
• Uart: 5
• Lin: 4
• Ssc: 2
• Ethernet: 1
• Sd / Emmc: 2
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: Yes
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 440
• Resistive Touch Screen: Yes
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: NO
• External Bus Interface: 2
• Dram Memory: DDR2/LPDDR, SDRAM/LPSDR
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 0.9 to 1.1
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

33.6
33.6.1
33.6.2
554
Product Dependencies
SAM9G45
I/O Lines
Power Management
The pins used for interfacing the USART may be multiplexed with the PIO lines. The program-
mer must first program the PIO controller to assign the desired USART pins to their peripheral
function. If I/O lines of the USART are not used by the application, they can be used for other
purposes by the PIO Controller.
To prevent the TXD line from falling when the USART is disabled, the use of an internal pull up
is mandatory. If the hardware handshaking feature is used, the internal pull up on TXD must
also be enabled.
Table 33-3.
The USART is not continuously clocked. The programmer must first enable the USART Clock in
the Power Management Controller (PMC) before using the USART. However, if the application
does not require USART operations, the USART clock can be stopped when not needed and be
restarted later. In this case, the USART will resume its operations where it left off.
Configuring the USART does not require the USART clock to be enabled.
Instance
USART0
USART0
USART0
USART0
USART0
USART1
USART1
USART1
USART1
USART1
USART2
USART2
USART2
USART2
USART2
USART3
USART3
USART3
USART3
USART3
I/O Lines
Signal
RXD0
SCK0
TXD0
RXD1
SCK1
TXD1
RXD2
SCK2
TXD2
CTS3
RXD3
SCK3
TXD3
CTS0
RTS0
CTS1
RTS1
CTS2
RTS2
RTS3
I/O Line
PD17
PD16
PD29
PC11
PD30
PB15
PB17
PB18
PB16
PB19
PA24
PA23
PA22
PB5
PB4
PC9
PB7
PB6
PB9
PB8
6438G–ATARM–19-Apr-11
Peripheral
B
B
A
B
A
A
A
A
B
A
B
B
A
B
A
B
B
A
B
A