MC68000 MOTOROLA [Motorola, Inc], MC68000 Datasheet - Page 190
MC68000
Manufacturer Part Number
MC68000
Description
Manufacturer
MOTOROLA [Motorola, Inc]
Datasheet
1.MC68000.pdf
(480 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MC68000-10/BZAJC
Manufacturer:
MOT
Quantity:
26
Company:
Part Number:
MC68000-8BXAJ
Manufacturer:
MOT
Quantity:
9
Company:
Part Number:
MC680008FN8
Manufacturer:
FREESCALE
Quantity:
8 831
Company:
Part Number:
MC68000FN10
Manufacturer:
MOT
Quantity:
5 510
Part Number:
MC68000FN10
Manufacturer:
MOTOROLA/摩托罗拉
Quantity:
20 000
Company:
Part Number:
MC68000FN12
Manufacturer:
MOT
Quantity:
5 510
Part Number:
MC68000L8
Manufacturer:
MOTOROLA/摩托罗拉
Quantity:
20 000
Part Number:
MC68000P10
Manufacturer:
MOT
Quantity:
20 000
- Current page: 190 of 480
- Download datasheet (2Mb)
Communications Processor (CP)
The HDLC controller uses the same data structure as the UART, BISYNC, and DDCMP con-
trollers. This data structure supports multibuffer operation and address comparisons.
The receive errors (overrun, nonoctet aligned frame, CD lost, aborted frame, and CRC error)
are reported through the receive BD. The transmit errors (underrun and CTS lost) are re-
ported through the transmit BD. An indication about the status of the lines (idle, CD, and
CTS) is reported through the SCC status register (SCCS), and a maskable interrupt is gen-
erated upon a status change in any one of those lines.
4.5.12.5 HDLC Command Set
The following commands are issued to the command register.
STOP TRANSMIT Command
RESTART TRANSMIT Command
4-70
After a hardware or software reset and the enabling of the channel in the SCC mode reg-
ister, the channel is in the transmit enable mode and starts polling the first BD in the table
approximately every eight or sixteen transmit clocks as determined by the FLG bit in the
HDLC mode register.
The channel STOP TRANSMIT command disables the transmission of frames on the
transmit channel. If this command is received by the HDLC controller during frame trans-
mission, transmission of that frame is aborted after the contents of the FIFO are transmit-
ted (up to four words). The TBD# is not advanced. No new BD is accessed, and no new
frames are transmitted for this channel. The transmitter will transmit an abort sequence (if
the command was given during frame transmission) and then begin to transmit flags or
idles as indicated by the HDLC mode register. The abort sequence on transmit is a zero
followed by seven ones (01111111).
This command is useful for performing frame retransmission. The M68000 core may issue
the STOP TRANSMIT command, reorganize the transmit BD table, and issue the RE-
START TRANSMIT command. The STOP TRANSMIT command may also be used in the
X.25 protocol to send a reject frame or a link reset command.
The STOP TRANSMIT command must be issued before the SCC mode register is used
to disable the transmitter if the transmitter is to be re-enabled at a later time.
The RESTART TRANSMIT command re-enables the transmission of characters on the
transmit channel. This command is expected by the HDLC controller after a STOP
TRANSMIT command, after a STOP TRANSMIT command and disabling the channel in
its SCC mode register, or after transmitter error (underrun or CTS lost when no automatic
frame retransmission is performed). The HDLC controller will resume transmission from
the current transmitter BD (TBD#) in the channel's transmit BD table.
If the transmitter is being re-enabled, the RESTART TRANSMIT command must be used
and should be followed by the enabling of the transmitter in the SCC mode register.
MC68302 USER’S MANUAL
MOTOROLA
Related parts for MC68000
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Motorola, Inc [VOLTAGE REGULATOR]
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
6367254 MOTOROLA SC (XSTRS/R F)
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
MC1494LMotorola, Inc [MONOLITHIC FOUR-QUADRANT MULTIPLIER]
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
MC1466LMotorola, Inc [PRECISION WIDE RANGE VOLTAGE AND CURRENT REGULATOR]
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
MC145532DWMotorola, Inc [ADPCM Transcoder]
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
Silicon Controlled Rectifiers
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
RF Power Field Effect Transistors N-Channel Enhancement-Mode Lateral MOSFETs
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
RF POWER FIELD EFFECT TRANSISTORS
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
LATERAL N-CHANNEL BROADBAND RF POWER MOSFETs
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
RF POWER FIELD EFFECT TRANSISTOR
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
RF LOW POWER TRANSISTOR NPN SILICON
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
PLASTIC SURFACE MOUNT ZENER DIODES 1.5 WATTS 3.3-68 VOLTS
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
OVERVOLTAGE TRANSIENT SUPPRESSOR
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
TMOS POWER FET 15 AMPERES 60 VOLTS
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
TMOS POWER FET LOGIC LEVEL 19 AMPERES 30 VOLTS RDS(on) = 0.099 OHM
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet: