LAN9211_0711 SMSC [SMSC Corporation], LAN9211_0711 Datasheet - Page 16
LAN9211_0711
Manufacturer Part Number
LAN9211_0711
Description
High-Performance Small Form Factor Single-Chip Ethernet Controller with HP Auto-MDIX
Manufacturer
SMSC [SMSC Corporation]
Datasheet
1.LAN9211_0711.pdf
(146 pages)
- Current page: 16 of 146
- Download datasheet (2Mb)
Revision 1.93 (11-27-07)
2.1
Host Address
PHY External Bias
Read Strobe
Write Strobe
FIFO Select
Chip Select
Host Data
Interrupt
Request
NAME
Resistor
NAME
TPO+
TPO-
TPI+
TPI-
Note: The pin names for the twisted pair pins shown above apply to a normal connection. If HP Auto-
Pin List
MDIX is enabled and a reverse connection is detected, or a reverse connection is manually
selected, the input pins become outputs, and vice-versa, as indicated in the descriptions.
FIFO_SEL
SYMBOL
D[15:0]
A[7:1]
nWR
nRD
nCS
IRQ
SYMBOL
EXRES1
TPO+
TPO-
TPI+
TPI-
BUFFER
O8/OD8
Table 2.1 Host Bus Interface Signals
TYPE
I/O8
Table 2.2 LAN Interface Signals
IS
IS
IS
IS
IS
BUFFER
TYPE
AO
AO
AI
AI
AI
DATASHEET
PINS
16
#
7
1
1
1
1
1
PINS
NUM
16
High-Performance Small Form Factor Single-Chip Ethernet Controller with HP Auto-MDIX
1
1
1
1
1
Bi-directional data port.
7-bit Address Port. Used to select Internal CSR’s and
When driven high all accesses to the LAN9211 are to
TX and RX FIFOs.
Active low strobe to indicate a read cycle.
Active low strobe to indicate a write cycle. This signal,
qualified with nCS, is also used to wakeup the
LAN9211 when it is in a reduced power state.
Active low signal used to qualify read and write
operations. This signal qualified with nWR is also used
to wakeup the LAN9211 when it is in a reduced power
state.
Programmable Interrupt request. Programmable
polarity, source and buffer types.
the RX or TX Data FIFOs. In this mode, the A[7:3]
upper address inputs are ignored.
Transmit Positive Output (normal)
Receive Positive Input (reversed)
Transmit Negative Output (normal)
Receive Negative Input (reversed)
Receive Positive Input (normal)
Transmit Positive Input (reversed)
Receive Negative Input (normal)
Transmit Negative Output (reversed)
Must be connected to ground through a 12.4K
ohm 1% resistor.
DESCRIPTION
DESCRIPTION
SMSC
Datasheet
LAN9211
Related parts for LAN9211_0711
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
FAST ETHERNET PHYSICAL LAYER DEVICE
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
4-PORT USB2.0 HUB CONTROLLER
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
FDC37C672ENHANCED SUPER I/O CONTROLLER WITH FAST IR
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
COM90C66LJPARCNET Controller/Transceiver with AT Interface and On-Chip RAM
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet: