Z8F042AHJ020SC00TR Zilog, Z8F042AHJ020SC00TR Datasheet - Page 121

• Manufacturer Part Number: Z8F042AHJ020SC00TR
• Description: IC ENCORE XP MCU FLASH 4K 28SSOP
• Manufacturer: Zilog
• Series: Encore!® XP®r

Specifications of Z8F042AHJ020SC00TR

• Core Processor: Z8
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: IrDA, UART/USART
• Peripherals: Brown-out Detect/Reset, LED, LVD, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 23
• Program Memory Size: 4KB (4K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 28-SSOP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: Z8F042AHJ020SC00T

®
Z8 Encore! XP
F082A Series
Product Specification
110
MPMD[1:0]—MULTIPROCESSOR Mode
If MULTIPROCESSOR (9-bit) mode is enabled,
00 = The UART generates an interrupt request on all received bytes (data and address).
01 = The UART generates an interrupt request only on received address bytes.
10 = The UART generates an interrupt request when a received address byte matches the
value stored in the Address Compare Register and on all successive data bytes until an
address mismatch occurs.
11 = The UART generates an interrupt request on all received data bytes for which the
most recent address byte matched the value in the Address Compare Register.
MPEN—MULTIPROCESSOR (9-bit) Enable
This bit is used to enable MULTIPROCESSOR (9-bit) mode.
0 = Disable MULTIPROCESSOR (9-bit) mode.
1 = Enable MULTIPROCESSOR (9-bit) mode.
MPBT—Multiprocessor Bit Transmit
This bit is applicable only when MULTIPROCESSOR (9-bit) mode is enabled. The 9th bit
is used by the receiving device to determine if the data byte contains address or data infor-
mation.
0 = Send a 0 in the multiprocessor bit location of the data stream (data byte).
1 = Send a 1 in the multiprocessor bit location of the data stream (address byte).
DEPOL—Driver Enable Polarity
0 = DE signal is Active High.
1 = DE signal is Active Low.
BRGCTL—Baud Rate Control
This bit causes an alternate UART behavior depending on the value of the REN bit in the
UART Control 0 Register.
When the UART receiver is not enabled (REN=0), this bit determines whether the Baud
Rate Generator issues interrupts.
0 = Reads from the Baud Rate High and Low Byte registers return the BRG Reload Value
1 = The Baud Rate Generator generates a receive interrupt when it counts down to 0.
Reads from the Baud Rate High and Low Byte registers return the current BRG count
value.
When the UART receiver is enabled (REN=1), this bit allows reads from the Baud Rate
Registers to return the BRG count value instead of the Reload Value.
0 = Reads from the Baud Rate High and Low Byte registers return the BRG Reload Value.
1 = Reads from the Baud Rate High and Low Byte registers return the current BRG count
value. Unlike the Timers, there is no mechanism to latch the Low Byte when the High
Byte is read.
RDAIRQ—Receive Data Interrupt Enable
0 = Received data and receiver errors generates an interrupt request to the Interrupt Con-
troller.
PS022825-0908
Universal Asynchronous Receiver/Transmitter