LIS302DLTR STMicroelectronics, LIS302DLTR Datasheet - Page 14

• Manufacturer Part Number: LIS302DLTR
• Description: ACCELEROMETER 3AXIS MEMS 14-LGA
• Manufacturer: STMicroelectronics

Specifications of LIS302DLTR

• Featured Product: STM32 Cortex-M3 Companion Products
• Axis: X, Y, Z
• Acceleration Range: ±2.3g, 9.2g
• Sensitivity: 18mg/digit, 72mg/digit
• Voltage - Supply: 2.16 V ~ 3.6 V
• Output Type: Digital
• Bandwidth: 100Hz ~ 400Hz Selectable
• Interface: I²C, SPI
• Mounting Type: Surface Mount
• Package / Case: 14-LGA
• Sensing Axis: X, Y, Z
• Acceleration: 2 g, 8 g
• Digital Output - Number Of Bits: 8 bit
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2.16 V
• Supply Current: 0.3 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Digital Output - Bus Interface: I2C, SPI
• Shutdown: Yes
• For Use With: 497-9047 - BOARD DEMO ACCELEROMETER DIL24497-8373 - BOARD EVAL EXTENSION SN250497-8204 - BOARD ADAPTER LIS302SG DIL24497-8203 - BOARD DEMO LIS302SG497-6404 - BOARD EVAL SPZB260 MOD FOR STR9497-6342 - BOARD EVALUATION FOR LIS302DL497-6246 - BOARD EVAL ACCELEROM LIS302ALK497-6227 - BOARD ADAPTER 20DIP LIS3LV02DL497-6226 - BOARD EVAL ACCELEROM LIS3LV02DL
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-5911-2

Mechanical and electrical specifications
2.4
Note:
2.5
2.5.1
14/42
Absolute maximum ratings
Stresses above those listed as “absolute maximum ratings” may cause permanent damage
to the device. This is a stress rating only and functional operation of the device under these
conditions is not implied. Exposure to maximum rating conditions for extended periods may
affect device reliability.
Table 7.
Supply voltage on any pin should never exceed 6.0V
Terminology
Sensitivity
Sensitivity describes the gain of the sensor and can be determined e.g. by applying 1g
acceleration to it. As the sensor can measure DC accelerations this can be done easily by
pointing the axis of interest towards the center of the Earth, noting the output value, rotating
the sensor by 180 degrees (point to the sky) and noting the output value again. By doing so,
±1g acceleration is applied to the sensor. Subtracting the larger output value from the
smaller one and dividing the result by 2 leads to the actual sensitivity of the sensor. This
value changes very little over temperature and also very little over time. The Sensitivity
Tolerance describes the range of Sensitivities of a large population of sensor.
Symbol
Vdd_IO
A
A
T
ESD
Vdd
T
Vin
POW
UNP
STG
OP
This is a mechanical shock sensitive device, improper handling can cause permanent
damages to the part
This is an ESD sensitive device, improper handling can cause permanent damages to
the part
Supply voltage
I/O pins supply voltage
Input voltage on any control pin
(CS, SCL/SPC, SDA/SDI/SDO)
Acceleration (any axis, powered, Vdd=2.5V)
Acceleration (any axis, unpowered)
Operating temperature range
Storage temperature range
Electrostatic discharge protection
Absolute maximum ratings
Ratings
-0.3 to Vdd_IO +0.3
10000g for 0.1 ms
10000g for 0.1 ms
Maximum value
3000g for 0.5 ms
3000g for 0.5 ms
-40 to +125
1.5 (CDM)
-40 to +85
200 (MM)
-0.3 to 6
-0.3 to 6
4 (HBM)
LIS302DL
Unit
kV
°C
°C
kV
V
V
V
V