LIS302DLTR STMicroelectronics, LIS302DLTR Datasheet - Page 18

• Manufacturer Part Number: LIS302DLTR
• Description: ACCELEROMETER 3AXIS MEMS 14-LGA
• Manufacturer: STMicroelectronics

Specifications of LIS302DLTR

• Featured Product: STM32 Cortex-M3 Companion Products
• Axis: X, Y, Z
• Acceleration Range: ±2.3g, 9.2g
• Sensitivity: 18mg/digit, 72mg/digit
• Voltage - Supply: 2.16 V ~ 3.6 V
• Output Type: Digital
• Bandwidth: 100Hz ~ 400Hz Selectable
• Interface: I²C, SPI
• Mounting Type: Surface Mount
• Package / Case: 14-LGA
• Sensing Axis: X, Y, Z
• Acceleration: 2 g, 8 g
• Digital Output - Number Of Bits: 8 bit
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2.16 V
• Supply Current: 0.3 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Digital Output - Bus Interface: I2C, SPI
• Shutdown: Yes
• For Use With: 497-9047 - BOARD DEMO ACCELEROMETER DIL24497-8373 - BOARD EVAL EXTENSION SN250497-8204 - BOARD ADAPTER LIS302SG DIL24497-8203 - BOARD DEMO LIS302SG497-6404 - BOARD EVAL SPZB260 MOD FOR STR9497-6342 - BOARD EVALUATION FOR LIS302DL497-6246 - BOARD EVAL ACCELEROM LIS302ALK497-6227 - BOARD ADAPTER 20DIP LIS3LV02DL497-6226 - BOARD EVAL ACCELEROM LIS3LV02DL
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-5911-2

Digital interfaces
5
5.1
18/42
Digital interfaces
The registers embedded inside the LIS302DL may be accessed through both the I
SPI serial interfaces. The latter may be SW configured to operate either in 3-wire or 4-wire
interface mode.
The serial interfaces are mapped onto the same pads. To select/exploit the I
line must be tied high (i.e connected to Vdd_IO).
Table 8.
I
The LIS302DL I
whose content can also be read back.
The relevant I
Table 9.
There are two signals associated with the I
Serial DAta line (SDA). The latter is a bidirectional line used for sending and receiving the
data to/from the interface. Both the lines are connected to Vdd_IO through a pull-up resistor
embedded inside the LIS302DL. When the bus is free both the lines are high.
The I
Normal Mode.
2
C Serial Interface
SDA/SDI/SDO
Transmitter
PIN name
2
SCL/SPC
Receiver
C interface is compliant with Fast Mode (400 kHz) I
Master
Term
Slave
SDO
CS
Serial interface pin description
Serial interface pin description
2
C terminology is given in the table below.
2
C is a bus slave. The I
SPI enable
I
I
SPI Serial Port Clock (SPC)
I
SPI Serial Data Input (SDI)
3-wire Interface Serial Data Output (SDO)
SPI Serial Data Output (SDO)
The device which sends data to the bus
The device which receives data from the bus
The device which initiates a transfer, generates clock signals and terminates a
transfer
The device addressed by the master
2
2
2
C/SPI mode selection (1: I
C Serial Clock (SCL)
C Serial Data (SDA)
2
C is employed to write the data into the registers
2
C bus: the Serial Clock Line (SCL) and the
2
C mode; 0: SPI enabled)
PIN description
Description
2
C standards as well as the
2
C interface, CS
LIS302DL
2
C and