LIS302DLTR STMicroelectronics, LIS302DLTR Datasheet - Page 32

• Manufacturer Part Number: LIS302DLTR
• Description: ACCELEROMETER 3AXIS MEMS 14-LGA
• Manufacturer: STMicroelectronics

Specifications of LIS302DLTR

• Featured Product: STM32 Cortex-M3 Companion Products
• Axis: X, Y, Z
• Acceleration Range: ±2.3g, 9.2g
• Sensitivity: 18mg/digit, 72mg/digit
• Voltage - Supply: 2.16 V ~ 3.6 V
• Output Type: Digital
• Bandwidth: 100Hz ~ 400Hz Selectable
• Interface: I²C, SPI
• Mounting Type: Surface Mount
• Package / Case: 14-LGA
• Sensing Axis: X, Y, Z
• Acceleration: 2 g, 8 g
• Digital Output - Number Of Bits: 8 bit
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2.16 V
• Supply Current: 0.3 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Digital Output - Bus Interface: I2C, SPI
• Shutdown: Yes
• For Use With: 497-9047 - BOARD DEMO ACCELEROMETER DIL24497-8373 - BOARD EVAL EXTENSION SN250497-8204 - BOARD ADAPTER LIS302SG DIL24497-8203 - BOARD DEMO LIS302SG497-6404 - BOARD EVAL SPZB260 MOD FOR STR9497-6342 - BOARD EVALUATION FOR LIS302DL497-6246 - BOARD EVAL ACCELEROM LIS302ALK497-6227 - BOARD ADAPTER 20DIP LIS3LV02DL497-6226 - BOARD EVAL ACCELEROM LIS3LV02DL
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-5911-2

Register description
7.13
7.14
32/42
FF_WU_DURATION_1 (33h)
Table 37.
Table 38.
Duration register for Free-Fall/Wake-Up interrupt 1. Duration step and maximum value
depend on the ODR chosen. Step 2.5 msec, from 0 to 637.5 msec if ODR=400Hz, else step
10 msec, from 0 to 2.55 sec when ODR=100Hz. The counter used to implement duration
function is blocked when LIR=1 in configuration register and the interrupt event is verified
FF_WU_CFG_2 (34h)
Table 39.
Table 40.
AOI
LIR
ZHIE
ZLIE
YHIE
YLIE
XHIE
XLIE
AOI
D7
D7-D0
FF_WU_DURATION_1 (33h) register
FF_WU_DURATION_1 (33h) register description
FF_WU_CFG_2 (34h) register
FF_WU_CFG_2 (34h) register description
And/or combination of Interrupt events. Default value: 0
(0: OR combination of interrupt events; 1: AND combination of interrupt events)
Latch interrupt request into FF_WU_SRC reg with the FF_WU_SRC reg cleared by
reading FF_WU_SRC_2 reg. Default value: 0
(0: interrupt request not latched; 1: interrupt request latched)
Enable interrupt generation on Z high event. Default value: 0
(0: disable interrupt request;
1: enable interrupt request on measured accel. value higher than preset threshold)
Enable interrupt generation on Z low event. Default value: 0
(0: disable interrupt request;
1: enable interrupt request on measured accel. value lower than preset threshold)
Enable interrupt generation on Y high event. Default value: 0
(0: disable interrupt request;
1: enable interrupt request on measured accel. value higher than preset threshold)
Enable interrupt generation on Y low event. Default value: 0
(0: disable interrupt request;
1: enable interrupt request on measured accel. value lower than preset threshold)
Enable interrupt generation on X high event. Default value: 0
(0: disable interrupt request;
1: enable interrupt request on measured accel. value higher than preset threshold)
Enable interrupt generation on X low event. Default value: 0
(0: disable interrupt request;
1: enable interrupt request on measured accel. value lower than preset threshold)
LIR
D6
Duration value. Default value: 0000 0000
ZHIE
D5
ZLIE
D4
YHIE
D3
YLIE
D2
XHIE
D1
LIS302DL
XLIE
D0