km416rd8as Samsung Semiconductor, Inc., km416rd8as Datasheet - Page 41

• Manufacturer Part Number: km416rd8as
• Description: 128mbit Rdram 256k X 16 Bit X 2*16 Dependent Banks Direct Rdramtm For Consumer Package
• Manufacturer: Samsung Semiconductor, Inc.

KM416RD8AS
Power State Management
Table 17 summarizes the power states available to a Direct
RDRAM. In general, the lowest power states have the
longest operational latencies. For example, the relative
power levels of PDN state and STBY state have a ratio of
about 1:110, and the relative access latencies to get read data
have a ratio of about 250:1.
PDN state is the lowest power state available. The informa-
tion in the RDRAM core is usually maintained with self-
refresh; an internal timer automatically refreshes all rows of
all banks. PDN has a relatively long exit latency because the
Figure 45 summarizes the transition conditions needed for
moving between the various power states. Note that NAP
and PDN have been divided into two substates (NAP-
A/NAP-S and PDN-A/PDN-S) to account for the fact that a
NAP or PDN exit may be made to either ATTN or STBY
states.
At initialization, the SETR/CLRR Reset sequence will put
the RDRAM into PDN-S state. The PDN exit sequence
involves an optional PDEV specification and bits on the
CMD and SIO
Once the RDRAM is in STBY, it will move to the
ATTN/ATTNR/ATTNW states when it receives a non-
broadcast ROWA packet or non-broadcast ROWR packet
with the ATTN command. The RDRAM returns to STBY
from these three states when it receives a RLX command.
Alternatively, it may enter NAP or PDN state from ATTN or
STBY states with a NAPR or PDNR command in an ROWR
packet. The PDN or NAP exit sequence involves an optional
PDEV specification and bits on the CMD and SIO0 pins.
PDN
STBY
ATTNR
Power
State
Powerdown state.
Standby state.
Ready for ROW
packets.
Attention read state.
Ready for ROW and COL
packets.
Sending Q (read data)
packets.
IN
pins.
Description
Self-refresh
REFA-refresh
TCLK/RCLK
ROW demux receiver
REFA-refresh
TCLK/RCLK
ROW demux receiver
COL demux receiver
DQ mux transmitter
Core power
Blocks consuming power
Table 17: Power State Summary
Page 38
NAP
ATTN
ATTNW
TCLK/RCLK block must resynchronize itself to the external
clock signal.
NAP state is another low-power state in which either self-
refresh or REFA-refresh are used to maintain the core. See
“Refresh” on page 43 for a description of the two refresh
mechanisms. NAP has a shorter exit latency than PDN
because the TCLK/RCLK block maintains its synchroniza-
tion state relative to the external clock signal at the time of
NAP entry. This imposes a limit (t
RDRAM may remain in NAP state before briefly returning
to STBY or ATTN to update this synchronization state.
The RDRAM returns to the ATTN or STBY state it was
originally in when it first entered NAP or PDN.
An RDRAM may only remain in NAP state for a time
t
The NAPRC command causes a napdown operation if the
RDRAM’s NCBIT is set. The NCBIT is not directly visible.
It is undefined on reset. It is set by a NAPR command to the
RDRAM, and it is cleared by an ACT command to the
RDRAM. It permits a controller to manage a set of
RDRAMs in a mixture of power states.
STBY state is the normal idle state of the RDRAM. In this
state all banks and sense amps have usually been left
precharged and ROWA and ROWR packets on the ROW
pins are being monitored. When a non-broadcast ROWA
packet or non-broadcast ROWR packet (with the ATTN
command) packet addressed to the RDRAM is seen, the
RDRAM enters ATTN state (see the right side of Figure 46).
This requires a time t
the specified row of the specified bank. A time
TFRM t
NLIMIT
Power
State
. It must periodically return to ATTN or STBY.
CYCLE
Nap state. Similar to PDN
except lower wake-up
latency.
Attention state.
Ready for ROW and COL
packets.
Attention write state.
Ready for ROW and COL
packets.
Ready for D (write data)
packets.
after the ROW packet, the RDRAM will be
Description
SA
during which the RDRAM activates
Target
Direct RDRAM
Rev. 0.9 July 1999
NLIMIT
Self-refresh or
TCLK/RCLK-Nap
REFA-refresh
TCLK/RCLK
ROW demux receiver
COL demux receiver
REFA-refresh
TCLK/RCLK
ROW demux receiver
COL demux receiver
DQ demux receiver
Core power
Blocks consuming power
REFA-refresh
) on how long an
™