PIC16F628A-I/ML Microchip Technology, PIC16F628A-I/ML Datasheet - Page 110

• Manufacturer Part Number: PIC16F628A-I/ML
• Description: IC MCU FLASH 2KX14 EEPROM 28QFN
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F628A-I/ML

• Core Size: 8-Bit
• Program Memory Size: 3.5KB (2K x 14)
• Core Processor: PIC
• Speed: 20MHz
• Connectivity: UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 224 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Controller Family/series: PIC16F
• No. Of I/o's: 16
• Eeprom Memory Size: 128Byte
• Ram Memory Size: 224Byte
• Cpu Speed: 20MHz
• No. Of Timers: 3
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 224 B
• Interface Type: SCI, USART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 1 x 16 bit
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163014, DM164120-4
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164324 - MODULE SKT FOR MPLAB 8DFN/16QFNXLT28QFN3 - SOCKET TRAN ICE 18DIP/28QFNI3DBF648 - BOARD DAUGHTER ICEPIC3AC164033 - ADAPTER 28QFN TO 18DIPAC162053 - HEADER INTERFACE ICD,ICD2 18DIPDV007003 - PROGRAMMER UNIVERSAL PROMATE II
• Data Converters: -
• Lead Free Status / Rohs Status: Details

PIC16F627A/628A/648A
14.5.1
External interrupt on the RB0/INT pin is edge triggered;
either rising if INTEDG bit (OPTION<6>) is set, or
falling, if INTEDG bit is clear. When a valid edge
appears
(INTCON<1>) is set. This interrupt can be disabled by
clearing the INTE control bit (INTCON<4>). The INTF
bit must be cleared in software in the interrupt service
routine before re-enabling this interrupt. The RB0/INT
interrupt can wake-up the processor from Sleep, if the
INTE bit was set prior to going into Sleep. The status of
the GIE bit decides whether or not the processor
branches to the interrupt vector following wake-up. See
Section 14.8 “Power-Down Mode (Sleep)” for details
on Sleep, and Figure 14-17 for timing of wake-up from
Sleep through RB0/INT interrupt.
14.5.2
An overflow (FFh → 00h) in the TMR0 register will set the
T0IF (INTCON<2>) bit. The interrupt can be enabled/
disabled by setting/clearing T0IE (INTCON<5>) bit. For
operation of the Timer0 module, see Section 6.0
“Timer0 Module”.
FIGURE 14-15:
DS40044G-page 110
Note 1:
OSC1
CLKOUT
INT pin
INTF flag
(INTCON<1>)
GIE bit
(INTCON<7>)
PC
Instruction
Fetched
Instruction
Executed
Instruction Flow
2:
3:
4:
5:
on
(3)
RB0/INT INTERRUPT
TMR0 INTERRUPT
INTF flag is sampled here (every Q1).
Asynchronous interrupt latency = 3-4 T
Latency is the same whether Inst (PC) is a single cycle or a two-cycle instruction.
CLKOUT is available in RC and INTOSC oscillator mode.
For minimum width of INT pulse, refer to AC specs.
INTF is enabled to be set anytime during the Q4-Q1 cycles.
the
Q1
Inst (PC - 1)
RB0/INT
Inst (PC)
(1)
INT PIN INTERRUPT TIMING
Q2
PC
(4)
Q3
pin,
(5)
Q4
Q1
the
Inst (PC + 1)
Inst (PC)
(1)
Q2
INTF
PC + 1
CY
Q3
. Synchronous latency = 3 T
bit
Q4
Interrupt Latency
Q1
Dummy Cycle
Q2
operation of PORTB (Section 5.2 “PORTB and TRISB
complete description of comparator interrupts.
14.5.3
An input change on PORTB <7:4> sets the RBIF
(INTCON<0>) bit. The interrupt can be enabled/disabled
by setting/clearing the RBIE (INTCON<3>) bit. For
Registers”).
14.5.4
See
PC + 1
—
Note:
Q3
Section 10.6
Q4
(2)
CY
If a change on the I/O pin should occur
when the read operation is being executed
(starts during the Q2 cycle and ends before
the start of the Q3 cycle), then the RBIF
interrupt flag may not get set.
PORTB INTERRUPT
COMPARATOR INTERRUPT
, where T
Q1
Dummy Cycle
Inst (0004h)
Q2
0004h
CY
“Comparator
Q3
© 2009 Microchip Technology Inc.
= instruction cycle time.
Q4
Q1
Interrupts”
Inst (0005h)
Q2
Inst (0004h)
0005h
Q3
Q4
for