P89LPC972FDH,129 NXP Semiconductors, P89LPC972FDH,129 Datasheet - Page 20

• Manufacturer Part Number: P89LPC972FDH,129
• Description: MCU 80C51 8KB FLASH 20TSSOP
• Manufacturer: NXP Semiconductors
• Series: LPC900r

Specifications of P89LPC972FDH,129

• Program Memory Type: FLASH
• Program Memory Size: 8KB (8K x 8)
• Package / Case: 20-TSSOP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 18MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 18
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: P89LPC
• Core: 80C51
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 18 MHz
• Number Of Programmable I/os: 15
• Number Of Timers: 5
• Operating Supply Voltage: 2.4 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 935290299129

NXP Semiconductors
P89LPC97X
Product data sheet
7.5 Clock output
7.6 On-chip RC oscillator option
7.7 Watchdog oscillator option
7.8 External clock input option
7.9 Clock source switching on the fly
The P89LPC970/971/972 supports a user-selectable clock output function on the
P3.0/XTAL2/CLKOUT pin when crystal oscillator is not being used. This condition occurs
if another clock source has been selected (on-chip RC oscillator, watchdog oscillator,
external clock input on XTAL1) and if the RTC and WDT are not using the crystal oscillator
as their clock source. This allows external devices to synchronize to the
P89LPC970/971/972. This output is enabled by the ENCLK bit in the TRIM register.
The frequency of this clock output is
in Idle mode, it may be turned off prior to entering Idle, saving additional power.
The P89LPC970/971/972 has a 6-bit TRIM register that can be used to tune the
frequency of the RC oscillator. During reset, the TRIM value is initialized to a factory
preprogrammed value to adjust the oscillator frequency to 7.373 MHz ± 1 % at room
temperature. End-user applications can write to the TRIM register to adjust the on-chip
RC oscillator to other frequencies. When the clock doubler option is enabled (UCFG2.7 =
1), the output frequency is 14.746 MHz. If CCLK is 8 MHz or slower, the CLKLP SFR bit
(AUXR1.7) can be set to logic 1 to reduce power consumption. On reset, CLKLP is logic 0
allowing highest performance access. This bit can then be set in software if CCLK is
running at 8 MHz or slower. When clock doubler option is enabled, BOE0 to BOE2 bits
(UCFG1[3:5]) are required to hold the device in reset at power-up until V
its specified level.
The watchdog has a separate oscillator which provides two options: 400 kHz and 25 kHz.
It is calibrated to ±10 % at 400 kHz. The oscillator can be used to save power when a high
clock frequency is not needed.
In this configuration, the processor clock is derived from an external source driving the
P3.1/XTAL1 pin. The rate may be from 0 Hz up to 18 MHz. The P3.0/XTAL2/CLKOUT pin
may be used as a standard port pin or a clock output. When using an oscillator frequency
above 12 MHz, BOE0 to BOE2 bits (UCFG1[3:5]) are required to hold the device in reset
at power-up until V
P89LPC970/971/972 can implement clock switching on any sources of watchdog
oscillator, 7 MHz/14 MHz internal RC oscillator, crystal oscillator and external clock input
during code is running. CLKOK bit in CLKCON register is used to indicate the clock switch
status. CLKOK is cleared when starting clock source switch and set when completed.
Notice that when CLKOK is ‘0’, writing to CLKCON register is not allowed.
All information provided in this document is subject to legal disclaimers.
DD
has reached its specified level.
Rev. 3 — 8 June 2010
8-bit microcontroller with accelerated two-clock 80C51 core
1
⁄
2
that of the CCLK. If the clock output is not needed
P89LPC970/971/972
© NXP B.V. 2010. All rights reserved.
DD
has reached
20 of 66