LPC2939FBD208,551 NXP Semiconductors, LPC2939FBD208,551 Datasheet - Page 29

• Manufacturer Part Number: LPC2939FBD208,551
• Description: IC ARM9 MCU FLASH 768KB 208-LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC2900r

Specifications of LPC2939FBD208,551

• Core Processor: ARM9
• Core Size: 32-Bit
• Speed: 125MHz
• Connectivity: CAN, EBI/EMI, I²C, LIN, SPI, UART/USART, USB, USB OTG
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 152
• Program Memory Size: 768KB (768K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 16K x 8
• Ram Size: 56K x 8
• Voltage - Supply (vcc/vdd): 1.71 V ~ 3.6 V
• Data Converters: A/D 24x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 208-LQFP
• Processor Series: LPC29
• Core: ARM968E-S
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: OM11027
• Package: 208LQFP
• Device Core: ARM968E-S
• Family Name: LPC2900
• Operating Supply Voltage: 1.8|3.3 V
• Data Bus Width: 16|32 Bit
• Number Of Programmable I/os: 160
• Interface Type: CAN/I2C/LIN/QSPI/UART/USB
• On-chip Adc: 24-chx10-bit
• Number Of Timers: 6
• For Use With: 568-4787 - BOARD EVAL LPC2939
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 935287113551

NXP Semiconductors
LPC2939_3
Product data sheet
6.10.2 Clock description
6.11.1 USB device controller
6.11.2 USB OTG controller
6.11 USB interface
The DMA controller is clocked by CLK_SYS_DMA derived from BASE_SYS_CLK, see
Section
The Universal Serial Bus (USB) is a 4-wire bus that supports communication between a
host and one or more (up to 127) peripherals. The bus supports hot plugging and dynamic
configuration of the devices. All transactions are initiated by the Host controller.
The LPC2939 USB interface includes a device and OTG controller with on-chip PHY for
device. The OTG switching protocol is supported through the use of an external controller.
Details on typical USB interfacing solutions can be found in
The device controller enables 12 Mbit/s data exchange with a USB Host controller. It
consists of a register interface, serial interface engine, endpoint buffer memory, and a
DMA controller. The serial interface engine decodes the USB data stream and writes data
to the appropriate endpoint buffer. The status of a completed USB transfer or error
condition is indicated via status registers. An interrupt is also generated if enabled. When
enabled, the DMA controller transfers data between the endpoint buffer and the on-chip
SRAM.
The USB device controller has the following features:
USB OTG (On-The-Go) is a supplement to the USB 2.0 specification that augments the
capability of existing mobile devices and USB peripherals by adding host functionality for
connection to USB peripherals.
The OTG Controller integrates the device controller, and a master-only I
implement OTG dual-role device functionality. The dedicated I
external OTG transceiver.
The USB OTG controller has the following features:
•
•
•
•
•
•
•
•
•
•
Fully compliant with USB 2.0 specification (full speed)
Supports 32 physical (16 logical) endpoints with a 2 kB endpoint buffer RAM
Supports Control, Bulk, Interrupt and Isochronous endpoints
Scalable realization of endpoints at run time
Endpoint Maximum packet size selection (up to USB maximum specification) by
software at run time
Supports SoftConnect and GoodLink features
While USB is in the Suspend mode, the LPC2939 can enter the Power-down mode
and wake up on USB activity
Supports DMA transfers with the on-chip SRAM blocks on all non-control endpoints
Allows dynamic switching between CPU-controlled slave and DMA modes
Double buffer implementation for Bulk and Isochronous endpoints
6.7.2.
All information provided in this document is subject to legal disclaimers.
Rev. 03 — 7 April 2010
ARM9 microcontroller with CAN, LIN, and USB
Section
2
C interface controls an
10.2.
LPC2939
© NXP B.V. 2010. All rights reserved.
2
C interface to
29 of 99