LPC2939FBD208,551 NXP Semiconductors, LPC2939FBD208,551 Datasheet - Page 74

• Manufacturer Part Number: LPC2939FBD208,551
• Description: IC ARM9 MCU FLASH 768KB 208-LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC2900r

Specifications of LPC2939FBD208,551

• Core Processor: ARM9
• Core Size: 32-Bit
• Speed: 125MHz
• Connectivity: CAN, EBI/EMI, I²C, LIN, SPI, UART/USART, USB, USB OTG
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 152
• Program Memory Size: 768KB (768K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 16K x 8
• Ram Size: 56K x 8
• Voltage - Supply (vcc/vdd): 1.71 V ~ 3.6 V
• Data Converters: A/D 24x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 208-LQFP
• Processor Series: LPC29
• Core: ARM968E-S
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: OM11027
• Package: 208LQFP
• Device Core: ARM968E-S
• Family Name: LPC2900
• Operating Supply Voltage: 1.8|3.3 V
• Data Bus Width: 16|32 Bit
• Number Of Programmable I/os: 160
• Interface Type: CAN/I2C/LIN/QSPI/UART/USB
• On-chip Adc: 24-chx10-bit
• Number Of Timers: 6
• For Use With: 568-4787 - BOARD EVAL LPC2939
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 935287113551

NXP Semiconductors
9. Dynamic characteristics
Table 36.
V
ground; positive currents flow into the IC; unless otherwise specified.
[1]
[2]
[3]
[4]
LPC2939_3
Product data sheet
Symbol
I/O pins
t
t
CLK_OUT pin
f
Internal clock
f
T
Low-power ring oscillator
f
t
Oscillator
f
t
PLL
f
f
t
t
Jitter specification for CAN
t
THL
TLH
clk
clk(sys)
ref(RO)
startup
i(osc)
startup
i(PLL)
o(PLL)
a(clk)
a(A)
jit(cc)(p-p)
DD(CORE)
clk(sys)
All parameters are guaranteed over the virtual junction temperature range by design. Pre-testing is performed at T
temperature on wafer level. Cased products are tested at T
test conditions to cover the specified temperature and power supply voltage range.
See
This parameter is not part of production testing or final testing, hence only a typical value is stated.
Oscillator start-up time depends on the quality of the crystal. For most crystals it takes about 1000 clock pulses until the clock is fully
stable.
Table
= V
Dynamic characteristics
DD(OSC_PLL)
27.
9.1 Dynamic characteristics: I/O and CLK_OUT pins, internal clock,
Parameter
HIGH to LOW transition
time
LOW to HIGH transition
time
clock frequency
system clock frequency
system clock period
RO reference
frequency
start-up time
oscillator input
frequency
start-up time
PLL input frequency
PLL output frequency
clock access time
address access time
cycle to cycle jitter
(peak-to-peak value)
oscillators, PLL, and CAN
; V
DD(IO)
= 2.7 V to 3.6 V; V
All information provided in this document is subject to legal disclaimers.
Conditions
C
C
on pin CLK_OUT
at maximum frequency
maximum frequency is
the clock input of an
external clock source
applied to the
XIN_OSC pin
at maximum frequency
CCO; direct mode
on TXDCn pin
L
L
= 30 pF
= 30 pF
Rev. 03 — 7 April 2010
DDA(ADC3V3)
amb
= 25 C (final testing). Both pre-testing and final testing use correlated
= 3.0 V to 3.6 V; all voltages are measured with respect to
[1]
ARM9 microcontroller with CAN, LIN, and USB
[2]
[2]
[3]
[3]
[4]
[3]
Min
4
4
-
10
8
0.4
-
10
-
10
10
156
-
-
-
Typ
-
-
-
-
-
0.5
6
-
500
-
-
-
-
-
0.4
Max
13.8
13.8
40
125
100
0.6
-
100
-
25
160
320
63.4
60.3
1
LPC2939
© NXP B.V. 2010. All rights reserved.
amb
= 85 C ambient
Unit
ns
ns
MHz
MHz
ns
MHz
s
MHz
s
MHz
MHz
MHz
ns
ns
ns
74 of 99