MC56F8014VFAE Freescale Semiconductor, MC56F8014VFAE Datasheet - Page 78

• Manufacturer Part Number: MC56F8014VFAE
• Description: IC DIGITAL SIGNAL CTRLR 32-LQFP
• Manufacturer: Freescale Semiconductor
• Series: 56F8xxxr

Specifications of MC56F8014VFAE

• Core Processor: 56800
• Core Size: 16-Bit
• Speed: 32MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 26
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Ram Size: 2K x 16
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 32-LQFP
• Cpu Family: 56F8xxx
• Device Core Size: 16b
• Frequency (max): 32MHz
• Interface Type: I2C/SCI/SPI
• Total Internal Ram Size: 4KB
• # I/os (max): 26
• Number Of Timers - General Purpose: 1
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 3V
• On-chip Adc: 2(4-chx12-bit)
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 105C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 32
• Package Type: LQFP
• Product: DSCs
• Data Bus Width: 16 bit
• Processor Series: MC56F80xx
• Core: 56800E
• Numeric And Arithmetic Format: Fixed-Point
• Device Million Instructions Per Second: 32 MIPs
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 26
• Data Ram Size: 4 KB
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Data Rom Size: 16 KB
• Development Tools By Supplier: MC56F8037EVM, DEMO56F8014-EE, DEMO56F8013-EE
• Minimum Operating Temperature: - 40 C
• For Use With: DEMO56F8014-E - BOARD DEMO MC56F8014 W/UNIV PSDEMO56F8014 - BOARD DEMO MC56F8014 W/US PSAPMOTOR56F8000E - KIT DEMO MOTOR CTRL SYSTEMDEMO56F8014-EE - BOARD DEMO FOR 56F8014
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

The power modes provide additional means to disable clock domains, configure the voltage regulator, and
configure clock generation to manage power utilization, as shown in
modes provide means of enabling/disabling the peripheral and/or core clocking as a group. Stop disable
controls are provided for selected peripherals in the control register so that these peripheral clocks can
optionally continue to operate in Stop mode and generate interrupts which will return the part from Stop
to Run mode. Standby mode provides normal operation but at very low speed and power utilization. It is
possible to invoke Stop or Wait mode while in Standby mode for even greater levels of power reduction.
A 200 kHz clock external clock can optionally be used in Standby mode to produce the required Standby
100 kHz system bus rate. Power-down mode, which selects the ROSC clock source but shuts it off, fully
disables the part and minimizes its power utilization but is only recoverable via reset.
When the PLL is not selected and the system bus is operating at around 100 kHz, the large regulator can
78
Wait
Stop
Standby
Power-Down
Mode
Table 6-3 Clock Operation in Power-Down Modes (Continued)
Core and memory
clocks disabled
Master clock generation in the OCCS
remains operational, but the SIM disables
the generation of system and peripheral
clocks.
The OCCS generates the 2x System Clock
at a reduced frequency (200 kHz). The PLL
and high speed peripheral clocks are
disabled and the high-speed peripheral
option is not available. System and
peripheral clocks operate at 100 kHz.
Master clock generation in the OCCS is
completely shut down. All system and
peripheral clocks are disabled.
Core Clocks
56F8014 Technical Data, Rev. 11
Peripheral clocks
enabled
Peripheral Clocks
Core executes WAIT instruction to enter this
mode.
Typically used for power-conscious applications.
Possible recoveries from Wait mode to Run
mode are:
1. Any interrupt
2. Executing a Debug mode entry command
during the 56800E core JTAG interface
2. Any reset (POR, external, software, COP)
Core executes STOP instruction to enter this
mode. Possible recoveries from Stop mode to
Run mode are:
1. Interrupt from Timer channels that have been
configured to operate in Stop mode (TCx_SD)
2. Interrupt for SCI configured to operate in Stop
mode (SCI_SD)
3. Low-voltage interrupt
4. Executing a Debug mode entry command
using the 56800E core JTAG interface
5. Any reset (POR, external, software, COP)
The user configures the OCCS and SIM to select
the relaxation oscillator clock source (PRECS),
shut down the PLL (PLLPD), put the relaxation
oscillator in Standby mode (ROSB), and put the
large regulator in Standby (LRSTDBY). The part
is fully operational, but operating at a minimum
frequency and power configuration. Recovery
requires reversing the sequence used to enter
this mode (allowing for PLL lock time).
The user configures the OCCS and SIM to enter
Standby mode as shown in the previous
description, followed by powering down the
oscillator (ROPD). The only possible recoveries
from this mode are:
1. External reset
2. Power-on reset
Table
Description
6-3. Run, Wait, and Stop
Freescale Semiconductor