MC56F8014VFAE Freescale Semiconductor, MC56F8014VFAE Datasheet - Page 98

• Manufacturer Part Number: MC56F8014VFAE
• Description: IC DIGITAL SIGNAL CTRLR 32-LQFP
• Manufacturer: Freescale Semiconductor
• Series: 56F8xxxr

Specifications of MC56F8014VFAE

• Core Processor: 56800
• Core Size: 16-Bit
• Speed: 32MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 26
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Ram Size: 2K x 16
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 32-LQFP
• Cpu Family: 56F8xxx
• Device Core Size: 16b
• Frequency (max): 32MHz
• Interface Type: I2C/SCI/SPI
• Total Internal Ram Size: 4KB
• # I/os (max): 26
• Number Of Timers - General Purpose: 1
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 3V
• On-chip Adc: 2(4-chx12-bit)
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 105C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 32
• Package Type: LQFP
• Product: DSCs
• Data Bus Width: 16 bit
• Processor Series: MC56F80xx
• Core: 56800E
• Numeric And Arithmetic Format: Fixed-Point
• Device Million Instructions Per Second: 32 MIPs
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 26
• Data Ram Size: 4 KB
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Data Rom Size: 16 KB
• Development Tools By Supplier: MC56F8037EVM, DEMO56F8014-EE, DEMO56F8013-EE
• Minimum Operating Temperature: - 40 C
• For Use With: DEMO56F8014-E - BOARD DEMO MC56F8014 W/UNIV PSDEMO56F8014 - BOARD DEMO MC56F8014 W/US PSAPMOTOR56F8000E - KIT DEMO MOTOR CTRL SYSTEMDEMO56F8014-EE - BOARD DEMO FOR 56F8014
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

10.2.1
The 56F8014 has two on-chip regulators. One supplies the PLL and relaxation oscillator. It has no external
pins and therefore has no external characteristics which must be guaranteed (other than proper operation
of the device). The second regulator supplies approximately 2.5 V to the 56F8014’s core logic. This
regulator requires an external 2.2 μF, or greater, capacitor for proper operation. Ceramic and tantalum
capacitors tend to provide better performance tolerances. The output voltage can be measured directly on
the V
10.3 AC Electrical Characteristics
Tests are conducted using the input levels specified in
propagation delays are measured from the 50% to the 50% point, and rise and fall times are measured
between the 10% and 90% points, as shown in
98
Input Voltage
Output Voltage
Short Circuit Current
Short Circuit Tolerance
(output shorted to ground)
CAP
1. When V
2. When V
3. Power-On Reset occurs whenever the internally regulated 2.5V digital supply drops below 1.8V. While
Low-Voltage Interrupt for 3.3V supply
Low-Voltage Interrupt for 2.5V supply
Low-Voltage Interrupt Recovery Hysteresis
Power-On Reset
pin. The specifications for this regulator are shown in
power is ramping up, this signal remains active for as long as the internal 2.5V is below 2.15V or the 3.3V
1/O voltage is below 2.7V, no matter how long the ramp-up rate is. The internally regulated voltage is
typically 100mV less than V
Voltage Regulator Specifications
Characteristic
DD
DD
drops below V
drops below V
Table 10-7 Power-On Reset Low-Voltage Parameters
Characteristic
3
EI3.3
EI32.5
Table 10-8. Regulator Parameters
DD
, an interrupt is generated.
, an interrupt is generated.
during ramp-up until 2.5V is reached, at which time it self-regulates.
56F8014 Technical Data, Rev. 11
1
2
Symbol
V
T
V
I
RSC
OUT
SS
IN
Figure
Symbol
V
V
POR
V
E12.5
EI3.3
EIH
10-2.
2.25
Min
3.0
—
—
2.60
2.05
Min
Table
—
—
Table
Typical
450
2.5
—
—
10-5. Unless otherwise specified,
10-8.
2.15
Typ
2.7
1.8
50
Max
2.75
650
3.6
30
Max
1.9
—
—
—
Freescale Semiconductor
Unit
mV
V
V
V
Minutes
Unit
mA
V
V