MCHC705JJ7CPE Freescale Semiconductor, MCHC705JJ7CPE Datasheet - Page 53

• Manufacturer Part Number: MCHC705JJ7CPE
• Description: IC MCU 8BIT 224 BYTES RAM 20PDIP
• Manufacturer: Freescale Semiconductor
• Series: HC05r

Specifications of MCHC705JJ7CPE

• Core Processor: HC05
• Core Size: 8-Bit
• Speed: 2.1MHz
• Connectivity: SIO
• Peripherals: POR, Temp Sensor, WDT
• Number Of I /o: 14
• Program Memory Size: 6KB (6K x 8)
• Program Memory Type: OTP
• Ram Size: 224 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 4x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-DIP (0.300", 7.62mm)
• Processor Series: HC705JJ
• Core: HC05
• Data Bus Width: 8 bit
• Data Ram Size: 224 B
• Interface Type: SIOP
• Maximum Clock Frequency: 2.1 MHz
• Number Of Programmable I/os: 14
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 4 Channel
• Package: 20PDIP
• Family Name: HC05
• Maximum Speed: 2.1 MHz
• Operating Supply Voltage: 3.3|5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

6.3.2 Wait Mode
The WAIT instruction puts the MCU in a low-power wait mode which consumes more power than the stop
mode and affects the MCU as follows:
The WAIT instruction does not affect any other bits, registers, or I/O lines.
These conditions restart the CPU bus clock and bring the MCU out of wait mode:
When the MCU exits the wait mode, there is no delay before code executes like occurs when exiting the
stop or halt modes.
6.3.3 Halt Mode
The STOP instruction puts the MCU in halt mode if selected by the SWAIT bit in the MOR. Halt mode is
identical to wait mode, except that a variable recovery delay occurs when the MCU exits halt mode. A
recovery time of from 1 to 16 or from 1 to 4064 internal bus cycles can be selected by the DELAY bit in
the MOR.
If the SWAIT bit is set in the MOR to put the MCU in halt mode, the COP watchdog cannot be turned off
inadvertently by a STOP instruction.
Freescale Semiconductor
•
•
•
•
•
•
•
•
•
•
•
Enables interrupts by clearing the I bit in the condition code register
Enables external interrupts by setting the IRQE bit in the IRQ status and control register
Stops the CPU clock which drives the address and data buses, but allows the selected oscillator
to continue to clock the core timer, programmable timer, analog subsystem, and SIOP
An external interrupt signal on the IRQ/V
the program counter with the contents of locations $1FFA and $1FFB.
An external interrupt signal on a port A external interrupt pin — If selected by PIRQ bit in the MOR,
a low-to-high transition on a PA3–PA0 pin loads the program counter with the contents of locations
$1FFA and $1FFB.
A core timer interrupt — A core timer overflow or a real-time interrupt loads the program counter
with the contents of locations $1FF8 and $1FF9.
A programmable timer interrupt — A programmable timer interrupt driven by an input capture,
output compare, or timer overflow loads the program counter with the contents of locations $1FF6
and $1FF7.
An SIOP interrupt — An SIOP interrupt driven by the completion of transmitted or received 8-bit
data loads the program counter with the contents of locations $1FF4 and $1FF5.
An analog subsystem interrupt — An analog subsystem interrupt driven by a voltage comparison
loads the program counter with the contents of locations $1FF2 and $1FF3.
A COP watchdog reset — A timeout of the COP watchdog resets the MCU and loads the program
counter with the contents of locations $1FFE and $1FFF. Software can enable real-time interrupts
so that the MCU can periodically exit the wait mode to reset the COP watchdog.
An external reset — A logic 0 on the RESET pin resets the MCU and loads the program counter
with the contents of locations $1FFE and $1FFF.
MC68HC705JJ7 • MC68HC705JP7 Advance Information Data Sheet, Rev. 4.1
PP
pin — A high-to-low transition on the IRQ/V
Low-Power Modes
PP
pin loads
53