MC9S12DT256MPVE Freescale Semiconductor, MC9S12DT256MPVE Datasheet - Page 525

• Manufacturer Part Number: MC9S12DT256MPVE
• Description: IC MCU 256K FLASH 25MHZ 112-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12DT256MPVE

• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 25MHz
• Connectivity: CAN, I²C, SCI, SPI
• Peripherals: PWM, WDT
• Number Of I /o: 91
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 12K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 5.25 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 112-LQFP
• Processor Series: S12D
• Core: HCS12
• Data Bus Width: 16 bit
• Data Ram Size: 12 KB
• Interface Type: CAN/I2C/SCI/SPI
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 91
• Number Of Timers: 1
• Operating Supply Voltage: 5 V to 2.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: M68KIT912DP256
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 2 (8-ch x 10-bit)
• No. Of I/o's: 91
• Eeprom Memory Size: 4KB
• Ram Memory Size: 12KB
• Cpu Speed: 25MHz
• No. Of Timers: 1
• No. Of Pwm Channels: 8
• Digital Ic Case Style: LQFP
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

12.3.2.4
Read: Anytime
Write: Has no effect
Freescale Semiconductor
Reset
SPTEF
MODF
Field
SPIF
7
5
4
W
R
SPIF
SPIF Interrupt Flag — This bit is set after a received data byte has been transferred into the SPI data register.
This bit is cleared by reading the SPISR register (with SPIF set) followed by a read access to the SPI data
register.
0 Transfer not yet complete.
1 New data copied to SPIDR.
SPI Transmit Empty Interrupt Flag — If set, this bit indicates that the transmit data register is empty. To clear
this bit and place data into the transmit data register, SPISR must be read with SPTEF = 1, followed by a write
to SPIDR. Any write to the SPI data register without reading SPTEF = 1, is effectively ignored.
0 SPI data register not empty.
1 SPI data register empty.
Mode Fault Flag — This bit is set if the SS input becomes low while the SPI is configured as a master and mode
fault detection is enabled, MODFEN bit of SPICR2 register is set. Refer to MODFEN bit description in
Section 12.3.2.2, “SPI Control Register 2
register (with MODF set) followed by a write to the SPI control register 1.
0 Mode fault has not occurred.
1 Mode fault has occurred.
SPI Status Register (SPISR)
0
7
= Unimplemented or Reserved
0
0
6
Figure 12-6. SPI Status Register (SPISR)
Table 12-7. SPISR Field Descriptions
SPTEF
MC9S12XDP512 Data Sheet, Rev. 2.21
1
5
(SPICR2)”. The flag is cleared automatically by a read of the SPI status
MODF
0
4
Description
0
0
3
Chapter 12 Serial Peripheral Interface (S12SPIV4)
0
0
2
0
0
1
0
0
0
525