UPD78F0535GB(T)-UEU-A NEC, UPD78F0535GB(T)-UEU-A Datasheet - Page 437
UPD78F0535GB(T)-UEU-A
Manufacturer Part Number
UPD78F0535GB(T)-UEU-A
Description
8BIT MCU, 60K FLASH, 3KB RAM, LQFP
Manufacturer
NEC
Datasheet
1.UPD78F0535GBT-UEU-A.pdf
(773 pages)
Specifications of UPD78F0535GB(T)-UEU-A
Controller Family/series
UPD78
No. Of I/o's
55
Ram Memory Size
3KB
Cpu Speed
20MHz
No. Of Timers
8
No. Of Pwm
RoHS Compliant
Core Size
8bit
Program Memory Size
60KB
Oscillator Type
External, Internal
- Current page: 437 of 773
- Download datasheet (6Mb)
17.5.4 Acknowledge (ACK)
side, it is assumed that reception has been correctly performed and processing is continued. Whether ACK has been
detected can be checked by using bit 2 (ACKD0) of IIC status register 0 (IICS0).
slave does not return ACK after receiving data, the master outputs a stop condition or restart condition and stops
transmission. If ACK is not returned, the possible causes are as follows.
of the IICS0 register is set by the data of the eighth bit that follows 7-bit address information. Usually, set ACKE0 to 1
for reception (TRC0 = 0).
slave must inform the master, by clearing ACKE0 to 0, that it will not receive any more data.
ACK is not generated. In this way, the master informs a slave at the transmission side that it does not require any
more data (transmission will be stopped).
address other than that of the local address is received, ACK is not generated (NACK).
ACK is used to check the status of serial data at the transmission and reception sides.
The reception side returns ACK each time it has received 8-bit data.
The transmission side usually receives ACK after transmitting 8-bit data. When ACK is returned from the reception
When the master receives the last data item, it does not return ACK and instead generates a stop condition. If a
<1> Reception was not performed normally.
<2> The final data item was received.
<3> The reception side specified by the address does not exist.
To generate ACK, the reception side makes the SDA0 line low at the ninth clock (indicating normal reception).
Automatic generation of ACK is enabled by setting bit 2 (ACKE0) of IIC control register 0 (IICC0) to 1. Bit 3 (TRC0)
If a slave can receive no more data during reception (TRC0 = 0) or does not require the next data item, then the
When the master does not require the next data item during reception (TRC0 = 0), it must clear ACKE0 to 0 so that
When the local address is received, ACK is automatically generated, regardless of the value of ACKE0. When an
When an extension code is received, ACK is generated if ACKE0 is set to 1 in advance.
How ACK is generated when data is received differs as follows depending on the setting of the wait timing.
• When 8-clock wait state is selected (bit 3 (WTIM0) of IICC0 register = 0):
• When 9-clock wait state is selected (bit 3 (WTIM0) of IICC0 register = 1):
By setting ACKE0 to 1 before releasing the wait state, ACK is generated at the falling edge of the eighth clock of
the SCL0 pin.
ACK is generated by setting ACKE0 to 1 in advance.
SDA0
SCL0
A6
1
CHAPTER 17 SERIAL INTERFACE IIC0
A5
2
User’s Manual U17260EJ6V0UD
Figure 17-16. ACK
A4
3
A3
4
A2
5
A1
6
A0
7
R/W
8
ACK
9
437
Related parts for UPD78F0535GB(T)-UEU-A
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
16/8 bit single-chip microcomputer
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Dual audio power amp circuit
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Dual comparator
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
MOS type composite field effect transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
50 V/100 mA FET array incorporating 2 N-ch MOSFETs
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Twin transistors equipped with different model chips(6P small MM)
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Bipolar analog integrated circuit
Manufacturer:
NEC
Datasheet: