UPD78F0535GB(T)-UEU-A NEC, UPD78F0535GB(T)-UEU-A Datasheet - Page 771

• Manufacturer Part Number: UPD78F0535GB(T)-UEU-A
• Description: 8BIT MCU, 60K FLASH, 3KB RAM, LQFP
• Manufacturer: NEC

Specifications of UPD78F0535GB(T)-UEU-A

• Controller Family/series: UPD78
• No. Of I/o's: 55
• Ram Memory Size: 3KB
• Cpu Speed: 20MHz
• No. Of Timers: 8
• No. Of Pwm: RoHS Compliant
• Core Size: 8bit
• Program Memory Size: 60KB
• Oscillator Type: External, Internal

5th edition
Edition
Addition of recommended resistance to Note of Figure 27-1 Connection Example
of QB-78K0MINI and
and Figure 27-2 Connection Example of QB-78K0MINI and
OCD1A/P31 and OCD1B/P32 Are Used)
Addition of Figure 27-3 Connection of FLMD0 Pin for Self Programming by
Means of On-Chip Debugging
Change of following items of Absolute Maximum Ratings
• Output current, high (addition of values of P20 to P27 and P121 to P124)
• Output current, low (addition of values of P20 to P27 and P121 to P124)
• Storage temperature
Addition of Note 2 to X1 Oscillator Characteristics
Addition of value when RSTS = 0 to 8 MHz internal oscillator in Internal Oscillator
Characteristics
Change of MIN. value in condition where 1.8 V ≤ V
oscillation clock frequency (f
Addition of recommended oscillator for X1 oscillation and XT1 oscillation and
oscillator constants
Change of following items of DC Characteristics
• Input voltage, high
• Input voltage, low
• Output voltage, low (addition of values in this condition: P60 to P63, 2.7 V ≤ V
• Input leakage current, high and Input leakage current, low (addition of FLMD0 and
• The condition of Pull-up resistor
• Supply current (change of values when square wave is input in operation mode and
• A/D converter operating current (addition of values while converter is not operating
• Watchdog timer operating current (Change of Note 8)
• LVI operating current (change of MAX. value)
Change of following items of AC Characteristics
• External main system clock input high-level width, low-level width in (1) Basic
• External subsystem clock input high-level width, low-level width in (1) Basic
• TI000, TI010, TI001, TI011 input high-level width, low-level width (addition of
• AC Timing Test Point in (1) Basic operation
• Transfer rate (change of values) in (2) Serial interface (a) UART6 and (b)
Addition of Note 2 to (1) Basic operation in AC Characteristics
Addition of MIN. and MAX. values as detection voltages of external input pin in LVI
Circuit Characteristics
Addition of Note 1 and value of write time to Basic Characteristics of Flash Memory
Programming Characteristics. Deletion of “(2) Serial write operation
characteristics” of the previous edition, and introduction of other manual
4.0 V, I
RESET in this condition of I
HALT mode, and addition of values for oscillator connection). Addition of values
where T
(when comparator operates). Addition of Note 7)
operation
operation
values in condition where 1.8 V ≤ V
UART0
OL1
A
= −40 to +70°C in STOP mode. Change of Notes 1, 2 , 4, and 5
= 5.0 mA)
µ
PD78F0537D (When OCD0A/X1 and OCD0B/X2 Are Used)
RL
LH1
) in Internal Oscillator Characteristics
APPENDIX E REVISION HISTORY
and I
User’s Manual U17260EJ6V0UD
Description
DD
LIL1
< 2.7 V) in (1) Basic operation
)
DD
< 2.7 V of internal low-speed
µ
PD78F0537D (When
DD
<
CHAPTER 27 ON-CHIP
DEBUG FUNCTION
(
CHAPTER 29
ELECTRICAL
SPECIFICATIONS
(STANDARD
PRODUCTS)
µ
PD78F0537D ONLY)
Chapter
(15/16)
771