AMD-8132BLCT AMD (ADVANCED MICRO DEVICES), AMD-8132BLCT Datasheet - Page 128

• Manufacturer Part Number: AMD-8132BLCT
• Manufacturer: AMD (ADVANCED MICRO DEVICES)

Specifications of AMD-8132BLCT

• Lead Free Status / RoHS Status: Not Compliant

AMD-8132™ HyperTransport™ PCI-X
128
17
16
15
14
13
Count Target Done / Count Retries.
Default = 0
Note: If Control[1] = 0, this bit is affected by Control[9:7].
Count Flushes / Count Reads.
Default = 0
Note: If Control[1] = 0, this bit is affected by Control[9:7].
Count Broadcasts / Count Writes.
Default = 0
Note: If Control[1] = 0, this bit is affected by Control[9:7].
Count Fences / Count Outbound Operations.
Default = 0
Note: If Control[1] = 0, this bit is affected by Control[9:7].
Count Nonposted Reads / Count Inbound Operations.
Default = 0
Note: If Control[1] =0, this bit is affected by Control[9:7].
• If Control[1] = 0 and this bit is set to 0, counting target done commands is disabled.
• If Control[1] = 1 and this bit is set to 0, counting retries is disabled.
• If Control[1] = 0 and this bit is set to 0, counting flush commands is disabled.
• If Control[1] = 1 and this bit is set to 0, counting read operations is disabled.
• If Control[1] = 0 and this bit is set to 0, counting broadcast commands is disabled.
• If Control[1] = 1 and this bit is set to 0, counting write operations is disabled.
• If Control[1] = 0 and this bit is set to 0, counting fence commands is disabled.
• If Control[1] = 1 and this bit is set to 0, counting outbound operations is disabled.
• If Control[1] = 0 and this bit is set to 0, counting nonposted read commands is disabled.
• If Control[1] = 1 and this bit is set to 0, counting inbound operations is disabled.
If Control[1] = 0 and this bit is set to 1, counting target done commands is enabled. Any
combination of Control[17:10] can be set, the count will be the total for all operations selected.
If Control[1] = 1 and this bit is set to 1, counting retries is enabled. Controlled by Control[16:13];
takes precedence over Control[23:18].
If Control[1] = 0 and this bit is set to 1, counting flush commands is enabled. Any combination of
Control[17:10] can be set, the count will be the total for all operations selected.
If Control[1] = 1 and this bit is set to 1, counting the read operation selected in Control[19:17] is
enabled. Operations selected here do not affect operations selected by bits Control[22:20].
If Control[1] = 0 and this bit is set to 1, counting broadcast commands is enabled. Any combination
of Control[17:10] can be set, the count will be the total for all operations selected.
If Control[1] = 1 and this bit is set to 1, counting the write operation selected in Control[19:17] is
enabled. Operations selected here do not affect operations selected by Control[22:20].
If Control[1] = 0 and this bit is set to 1, counting fence commands is enabled. Any combination of
Control[17:10] can be set, the count will be the total for all operations selected.
If Control[1] = 1 and this bit is set to 1, counting outbound operations selected in Control[22:17] is
enabled.
If Control[1] = 0 and this bit is set to 1, counting nonposted read commands is enabled. Any
combination of Control[17:10] can be set, the count will be the total for all operations selected.
If Control[1] = 1 and this bit is set to 1, counting inbound operations selected in Control[22:17] is
enabled.
®
2.0 Tunnel Data Sheet
Registers
26792 Rev. 3.07 July 2005
Chapter 3