CS42428-CQZ Cirrus Logic Inc, CS42428-CQZ Datasheet - Page 17

• Manufacturer Part Number: CS42428-CQZ
• Description: IC CODEC 8CH PLL 192KHZ 64-LQFP
• Manufacturer: Cirrus Logic Inc
• Type: Audio Codecr

Specifications of CS42428-CQZ

• Data Interface: Serial
• Resolution (bits): 24 b
• Number Of Adcs / Dacs: 2 / 8
• Sigma Delta: Yes
• Dynamic Range, Adcs / Dacs (db) Typ: 114 / 114
• Voltage - Supply, Analog: 4.75 V ~ 5.25 V
• Voltage - Supply, Digital: 3.13 V ~ 5.25 V
• Operating Temperature: -10°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 64-LQFP
• Audio Codec Type: Stereo
• No. Of Adcs: 2
• No. Of Dacs: 8
• No. Of Input Channels: 2
• No. Of Output Channels: 15
• Adc / Dac Resolution: 24bit
• Sampling Rate: 192kSPS
• Ic Interface Type: I2C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 598-1499 - BOARD EVAL FOR CS42428 CODEC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 598-1031

DS605F1
RST
AINR-
AINR+
AINL+
AINL-
VQ
FILT+
REFGND
AOUTA1 +,-
AOUTB1 +,-
AOUTA2 +,-
AOUTB2 +,-
AOUTA3 +,-
AOUTB3 +,-
AOUTA4 +,-
AOUTB4 +,-
VA
AGND
MUTEC
LPFLT
GPO7
GPO6
GPO5
GPO4
GPO3
GPO2
GPO1
VLS
RMCK
ADC_SDOUT
ADCIN1
ADCIN2
OMCK
ADC_LRCK
ADC_SCLK
36,37
35,34
32,33
31,30
28,29
27,26
22,23
21,20
12
13
14
15
16
17
18
19
24
41
25
40
38
39
42
43
44
45
46
47
48
53
55
56
58
57
59
60
61
Reset (Input) - The device enters a low power mode and all internal registers are reset to their default
settings when low.
Differential Right Channel Analog Input (Input) - Signals are presented differentially to the delta-sigma
modulators via the AINR+/- pins.
Differential Left Channel Analog Input (Input) - Signals are presented differentially to the delta-sigma
modulators via the AINL+/- pins.
Quiescent Voltage (Output) - Filter connection for internal quiescent reference voltage.
Positive Voltage Reference (Output) - Positive reference voltage for the internal sampling circuits.
Reference Ground (Input) - Ground reference for the internal sampling circuits.
Differential Analog Output (Output) - The full-scale differential analog output level is specified in the
Analog Characteristics specification table.
Analog Power (Input) - Positive power supply for the analog section.
Analog Ground (Input) - Ground reference. Should be connected to analog ground.
Mute Control (Output) - The Mute Control pin outputs high impedance following an initial power-on con-
dition or whenever the PDN bit is set to a ‘1’, forcing the codec into power-down mode. The signal will
remain in a high impedance state as long as the part is in power-down mode. The Mute Control pin goes
to the selected “active” state during reset, muting, or if the master clock to left/right clock frequency ratio
is incorrect. This pin is intended to be used as a control for external mute circuits to prevent the clicks
and pops that can occur in any single supply system. The use of external mute circuits are not manda-
tory but may be desired for designs requiring the absolute minimum in extraneous clicks and pops.
PLL Loop Filter (Output) - An RC network should be connected between this pin and ground.
General Purpose Output (Output) - These pins can be configured as general purpose output pins, an
ADC overflow interrupt or Mute Control outputs according to the General Purpose Pin Control registers.
Serial Port Interface Power (Input) - Determines the required signal level for the serial port interfaces.
Recovered Master Clock (Output) - Recovered master clock output from the External Clock Reference
(OMCK, pin 59) or the PLL which is locked to the incoming ADC_LRCK.
ADC Serial Data Output (Output) - Output for two’s complement serial audio PCM data from the output
of the internal and external ADCs.
External ADC Serial Input (Input) - The CS42428 provides for up to two external stereo analog to digital
converter inputs to provide a maximum of six channels on one serial data output line when the CS42428
is placed in One-Line Mode.
External Reference Clock (Input) - External clock reference that must be within the ranges specified in
the register
ADC Left/Right Clock (Input/Output) - Determines which channel, Left or Right, is currently active on
the ADC serial audio data line.
ADC Serial Clock (Input/Output) - Serial clock for the ADC serial audio interface.
“OMCK Frequency (OMCK Freqx)” on page
48.
CS42428
17