LAN9311-NU SMSC, LAN9311-NU Datasheet - Page 129

• Manufacturer Part Number: LAN9311-NU
• Description: IC ETHER SW 2PRT 16BIT 128-VTQFP
• Manufacturer: SMSC
• Type: Two Port Managed Ethernet Switchr

Specifications of LAN9311-NU

• Controller Type: Ethernet Switch Controller
• Interface: Serial EEPROM
• Voltage - Supply: 3.3V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 128-TQFP, 128-VQFP
• Product: Ethernet Switches
• Number Of Transceivers: 1
• Standard Supported: 802.3, 802.3u
• Data Rate: 10 MB, 100 MB
• Supply Voltage (max): 3.3 V
• Supply Voltage (min): 0 V
• Maximum Operating Temperature: + 70 C
• Ethernet Connection Type: 10 Base-T, 100 Base-TX
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• For Use With: 638-1076 - EVALUATION BOARD LAN9311-NU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Supply: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 638-1075

Two Port 10/100 Managed Ethernet Switch with 16-Bit Non-PCI CPU Interface
Datasheet
SMSC LAN9311/LAN9311i
9.8.5
9.8.6
9.8.6.1
BITS
6:3
8
7
2
1
0
Excessive Collisions. When set, this bit indicates that the transmission was aborted after 16
collisions while attempting to transmit the current packet.
Reserved. This bit is reserved. Always write zeros to this field to guarantee future compatibility.
Collision Count. This counter indicates the number of collisions that occurred before the packet was
transmitted. It is not valid when excessive collisions (bit 8) is also set.
Excessive Deferral. If the deferred bit is set in the control register, the setting of the excessive
deferral bit indicates that the transmission has ended because of a deferral of over 24288 bit times
during transmission.
Reserved. This bit is reserved. Always write zeros to this field to guarantee future compatibility
Deferred. When set, this bit indicates that the current packet transmission was deferred.
Calculating Actual TX Data FIFO Usage
The following rules are used to calculate the actual TX Data FIFO space consumed by a TX Packet:
Transmit Examples
TX Example 1
In this example a single, 111-Byte Ethernet packet will be transmitted. This packet is divided into three
buffers. The three buffers are as follows:
Buffer 0:
Buffer 1:
Buffer 2:
TX command 'A' is stored in the TX Data FIFO for every TX buffer
TX command 'B' is written into the TX Data FIFO when the First Segment (FS) bit is set in TX
command 'A'
Any DWORD-long data added as part of the “Data Start Offset” is removed from each buffer before
the data is written to the TX Data FIFO. Any data that is less than 1 DWORD is passed to the TX
Data FIFO.
Payload from each buffer within a Packet is written into the TX Data FIFO.
Any DWORD-long data added as part of the End Padding is removed from each buffer before the
data is written to the TX Data FIFO. Any end padding that is less than 1 DWORD is passed to the
TX Data FIFO
7-Byte “Data Start Offset”
79-Bytes of payload data
16-Byte “Buffer End Alignment”
0-Byte “Data Start Offset”
15-Bytes of payload data
16-Byte “Buffer End Alignment”
10-Byte “Data Start Offset”
17-Bytes of payload data
16-Byte “Buffer End Alignment”
DATASHEET
129
DESCRIPTION
Revision 1.7 (06-29-10)