LAN9311-NU SMSC, LAN9311-NU Datasheet - Page 247

• Manufacturer Part Number: LAN9311-NU
• Description: IC ETHER SW 2PRT 16BIT 128-VTQFP
• Manufacturer: SMSC
• Type: Two Port Managed Ethernet Switchr

Specifications of LAN9311-NU

• Controller Type: Ethernet Switch Controller
• Interface: Serial EEPROM
• Voltage - Supply: 3.3V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 128-TQFP, 128-VQFP
• Product: Ethernet Switches
• Number Of Transceivers: 1
• Standard Supported: 802.3, 802.3u
• Data Rate: 10 MB, 100 MB
• Supply Voltage (max): 3.3 V
• Supply Voltage (min): 0 V
• Maximum Operating Temperature: + 70 C
• Ethernet Connection Type: 10 Base-T, 100 Base-TX
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• For Use With: 638-1076 - EVALUATION BOARD LAN9311-NU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Supply: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 638-1075

Two Port 10/100 Managed Ethernet Switch with 16-Bit Non-PCI CPU Interface
Datasheet
SMSC LAN9311/LAN9311i
14.2.8.1
31:16
BITS
15
14
13
12
11
10
9
8
RESERVED
(See
Reset (VPHY_RST)
When set, this bit resets all the Virtual PHY registers to their default state.
This bit is self clearing.
0: Normal Operation
1: Reset
Loopback (VPHY_LOOPBACK)
This bit enables/disables the loopback mode. When enabled, transmissions
from the Host MAC are not sent to the switch fabric. Instead, they are looped
back onto the receive path.
0: Loopback mode disabled (normal operation)
1: Loopback mode enabled
Speed Select LSB (VPHY_SPEED_SEL_LSB)
This bit is used to set the speed of the Virtual PHY when the
Negotiation (VPHY_AN)
0: 10 Mbps
1: 100 Mbps
Auto-Negotiation (VPHY_AN)
This bit enables/disables Auto-Negotiation. When enabled, the
LSB (VPHY_SPEED_SEL_LSB)
are overridden.
0: Auto-Negotiation disabled
1: Auto-Negotiation enabled
Power Down (VPHY_PWR_DWN)
This bit is not used by the Virtual PHY and has no effect.
Isolate (VPHY_ISO)
This bit is not used by the Virtual PHY and has no effect.
Restart Auto-Negotiation (VPHY_RST_AN)
When set, this bit updates the emulated Auto-Negotiation results.
0: Normal operation
1: Auto-Negotiation restarted
Duplex Mode (VPHY_DUPLEX)
This bit is used to set the duplex when the
is disabled.
0: Half Duplex
1: Full Duplex
Virtual PHY Basic Control Register (VPHY_BASIC_CTRL)
This read/write register is used to configure the Virtual PHY.
Note: This register is re-written in its entirety by the EEPROM Loader following the release or reset
Note
or a RELOAD command. Refer to
information.
14.16)
Offset:
Index (decimal):
bit is disabled.
1C0h
0
DESCRIPTION
and
Duplex Mode (VPHY_DUPLEX)
DATASHEET
Auto-Negotiation (VPHY_AN)
247
Section 10.2.4, "EEPROM Loader," on page 150
Size:
Speed Select
Auto-
32 bits
bits
bit
TYPE
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
RO
SC
SC
Revision 1.7 (06-29-10)
DEFAULT
0b
0b
0b
1b
0b
0b
0b
0b
for more
-