PIC16F1827-E/P Microchip Technology Inc., PIC16F1827-E/P Datasheet - Page 131

• Manufacturer Part Number: PIC16F1827-E/P
• Description: 7 KB Flash, 384 bytes RAM, 32 MHz Int. Osc, 16 I/0, Enhanced Mid Range Core
• Manufacturer: Microchip Technology Inc.

Specifications of PIC16F1827-E/P

• A/d Inputs: 12-Channel, 10-Bit
• Comparators: 2
• Cpu Speed: 8 MIPS
• Eeprom Memory: 256 Bytes
• Input Output: 16
• Interface: CAN/I2C/SPI/UART/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 18-pin PDIP
• Programmable Memory: 7K Bytes
• Ram Size: 384 Bytes
• Speed: 32 MHz
• Timers: 4-8-bit, 1-16-bit
• Voltage, Range: 1.8-5.5 V
• Standby Current (pic16lf182x): 30 nA @ 1.8 V, Typical

13.0
The PORTB pins can be configured to operate as
Interrupt-On-Change (IOC) pins. An interrupt can be
generated by detecting a signal that has either a rising
edge or a falling edge. Any individual PORTB pin can
be
interrupt-on-change module has the following features:
• Interrupt-on-Change enable (Master Switch)
• Individual pin configuration
• Rising and falling edge detection
• Individual pin interrupt flags
Figure 13-1
13.1
To allow individual port pins to generate an interrupt, the
IOCIE bit of the INTCON register must be set. If the
IOCIE bit is disabled, the edge detection on the pin will
still occur, but an interrupt will not be generated.
13.2
For each port pin, a rising edge detector and a falling
edge detector are present. To enable a pin to detect a
rising edge, the associated IOCBPx bit of the IOCBP
register is set. To enable a pin to detect a falling edge,
the associated IOCBNx bit of the IOCBN register is set.
A pin can be configured to detect rising and falling
edges simultaneously by setting both the IOCBPx bit
and the IOCBNx bit of the IOCBP and IOCBN registers,
respectively.
FIGURE 13-1:
 2011 Microchip Technology Inc.
configured
RBx
INTERRUPT-ON-CHANGE
Enabling the Module
Individual Pin Configuration
is a block diagram of the IOC module.
IOCBNx
IOCBPx
to
generate
INTERRUPT-ON-CHANGE BLOCK DIAGRAM
D
CK
D
CK
an
R
R
Q
Q
interrupt.
The
Q2 Clock Cycle
individual pin detectors
From all other IOCBFx
13.3
The IOCBFx bits located in the IOCBF register are
status flags that correspond to the Interrupt-on-change
pins of the port. If an expected edge is detected on an
appropriately enabled pin, then the status flag for that pin
will be set, and an interrupt will be generated if the IOCIE
bit is set. The IOCIF bit of the INTCON register reflects
the status of all IOCBFx bits.
13.4
The individual status flags, (IOCBFx bits), can be
cleared by resetting them to zero. If another edge is
detected during this clearing operation, the associated
status flag will be set at the end of the sequence,
regardless of the value actually being written.
In order to ensure that no detected edge is lost while
clearing flags, only AND operations masking out known
changed bits should be performed. The following
sequence is an example of what should be performed.
EXAMPLE 13-1:
13.5
The interrupt-on-change interrupt sequence will wake
the device from Sleep mode, if the IOCIE bit is set.
If an edge is detected while in Sleep mode, the IOCBF
register will be updated prior to the first instruction
executed out of Sleep.
IOCBFx
ANDWF
MOVLW
XORWF
PIC16(L)F1826/27
Interrupt Flags
Clearing Interrupt Flags
Operation in Sleep
0xff
IOCBF, W
IOCBF, F
IOCIE
DS41391D-page 131
IOC Interrupt to
CPU Core