AT32UC3C2256C Atmel Corporation, AT32UC3C2256C Datasheet - Page 68

• Manufacturer Part Number: AT32UC3C2256C
• Manufacturer: Atmel Corporation

Specifications of AT32UC3C2256C

• Flash (kbytes): 256 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 45
• Ext Interrupts: 64
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 5
• Twi (i2c): 2
• Uart: 4
• Can: 2
• Lin: 4
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 2
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 68
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6 or 4.5 to 5.5
• Operating Voltage (vcc): 3.0 to 3.6 or 4.5 to 5.5
• Fpu: Yes
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 13
• Input Capture Channels: 6
• Pwm Channels: 14
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

8.3.1
8.3.1.1
8.3.1.2
68
AVR32
Description of events in AVR32A
Reset Exception
OCD Stop CPU Exception
The addresses of the interrupt routines are calculated by adding the address on the autovector
offset bus to the value of the Exception Vector Base Address (EVBA). The INT0, INT1, INT2,
INT3, and NMI signals indicate the priority of the pending interrupt. INT0 has the lowest priority,
and NMI the highest priority of the interrupts. Implementations may require that EVBA is aligned
in an IMPLEMENTATION DEFINED way in order to support autovectoring.
The Reset exception is generated when the reset input line to the CPU is asserted. The Reset
exception can not be masked by any bit. The Reset exception resets all synchronous elements
and registers in the CPU pipeline to their default value, and starts execution of instructions at
address 0x8000_0000.
All other system registers are reset to their reset value, which may or may not be defined. Refer
to the Programming Model chapter for details.
The OCD Stop CPU exception is generated when the OCD Stop CPU input line to the CPU is
asserted. The OCD Stop CPU exception can not be masked by any bit. This exception is identi-
cal to a non-maskable, high priority breakpoint. Any subsequent operation is controlled by the
OCD hardware. The OCD hardware will take control over the CPU and start to feed instructions
directly into the pipeline.
SR = reset_value_of_SREG;
PC = 0x8000_0000;
RSR_DBG = SR;
RAR_DBG = PC;
SR[M2:M0] = B’110;
SR[R] = 0;
SR[J] = 0;
SR[D] = 1;
SR[DM] = 1;
SR[EM] = 1;
SR[GM] = 1;
32000D–04/2011