ST7MC2S6 STMicroelectronics, ST7MC2S6 Datasheet - Page 23
![no-image](/images/manufacturer_photos/0/6/637/stmicroelectronics_sml.jpg)
ST7MC2S6
Manufacturer Part Number
ST7MC2S6
Description
8-BIT MCU WITH NESTED INTERRUPTS, FLASH, 10-BIT ADC,BRUSHLESS MOTOR CONTROL, 5 TIMERS, SPI, LINSCI(TM)
Manufacturer
STMicroelectronics
Datasheet
1.ST7MC1K4.pdf
(309 pages)
Specifications of ST7MC2S6
Hdflash Endurance
100 cycles, data retention
Clock Sources
crystal/ceramic resonator oscillators and by-pass for external clock, clock security system.
Four Power Saving Modes
Halt, Active-Halt, Wait and Slow
Main Clock Controller With
Real time base, Beep and Clock-out capabilities
Two 16-bit Timers With
2 input captures, 2 output compares, external clock input, PWM and pulse generator modes
8-bit Pwm Auto-reload Timer With
2 input captures, 4 PWM outputs, output compare and time base interrupt, external clock with event detector
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 23 of 309
- Download datasheet (6Mb)
FLASH PROGRAM MEMORY (Cont’d)
4.4 ICC INTERFACE
ICC (In-Circuit Communication) needs a minimum
of four and up to six pins to be connected to the
programming tool (see
Figure 10. Typical ICC Interface
Notes:
1. If the ICCCLK or ICCDATA pins are only used
as outputs in the application, no signal isolation is
necessary. As soon as the Programming Tool is
plugged to the board, even if an ICC session is not
in progress, the ICCCLK and ICCDATA pins are
not available for the application. If they are used as
inputs by the application, isolation such as a serial
resistor has to implemented in case another de-
vice forces the signal. Refer to the Programming
Tool documentation for recommended resistor val-
ues.
2. During the ICC session, the programming tool
must control the RESET pin. This can lead to con-
flicts between the programming tool and the appli-
cation reset circuit if it drives more than 5mA at
high level (push pull output or pull-up resistor<1K).
A schottky diode can be used to isolate the appli-
cation RESET circuit in this case. When using a
classical RC network with R > 1K or a reset man-
– RESET: device reset
– V
APPLICATION
POWER SUPPLY
SS
: device power supply ground
(See Note 3)
PROGRAMMING TOOL
C
L2
Figure
10). These pins are:
OPTIONAL
(See Note 4)
C
ST7
L1
10kΩ
10
ICC CONNECTOR
9
agement IC with open drain output and pull-up
resistor > 1K, no additional components are need-
ed. In all cases the user must ensure that no exter-
nal reset is generated by the application during the
ICC session.
3. The use of Pin 7 of the ICC connector depends
on the Programming Tool architecture. This pin
must be connected when using most ST Program-
ming Tools (it is used to monitor the application
power supply). Please refer to the Programming
Tool manual.
4. Pin 9 has to be connected to the OSC1 or OS-
CIN pin of the ST7 when the clock is not available
in the application or if the selected clock option is
not programmed in the option byte. ST7 devices
with multi-oscillator capability need to have OSC2
grounded in this case.
7
8
– ICCCLK: ICC output serial clock pin
– ICCDATA: ICC input/output serial data pin
– ICCSEL/V
– OSC1(or OSCIN): main clock input for exter-
– V
nal source (optional)
ure
5
6
ICC Cable
DD
4
3
10, Note 3)
: application board power supply (see
1
2
PP
HE10 CONNECTOR TYPE
: programming voltage
ICC CONNECTOR
ST7MC1xx/ST7MC2xx
APPLICATION BOARD
APPLICATION
See Note 2
APPLICATION
RESET SOURCE
See Note 1
I/O
23/309
Fig-
1
Related parts for ST7MC2S6
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![ST7MC-KIT/BLDC](/photos/39/38/393887/st7mc-kit_tmb.jpg)
Part Number:
Description:
KIT STARTER COMPLETE MOTOR CTRL
Manufacturer:
STMicroelectronics
Datasheet:
![ST7MC-MOT/IND](/photos/39/38/393887/st7mc-kit_tmb.jpg)
Part Number:
Description:
KIT STARTER SOFTEC MOTOR CTRL
Manufacturer:
STMicroelectronics
Datasheet:
![HCF4040BF](/images/manufacturer_photos/0/6/637/stmicroelectronics_tmb.jpg)
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
![HCF4054BF](/images/manufacturer_photos/0/6/637/stmicroelectronics_tmb.jpg)
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
![STEVAL-MKI062V2](/photos/28/39/283999/steval-mki062v2_tmb.jpg)
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
![BUT32V](/images/manufacturer_photos/0/6/637/stmicroelectronics_tmb.jpg)
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet:
![STTA12006TV2](/images/manufacturer_photos/0/6/637/stmicroelectronics_tmb.jpg)
Part Number:
Description:
TURBOSWITCH ULTRA-FAST HIGH VOLTAGE DIODE
Manufacturer:
STMicroelectronics
Datasheet:
![E110NS20FD](/images/manufacturer_photos/0/6/637/stmicroelectronics_tmb.jpg)
Part Number:
Description:
Manufacturer:
STMicroelectronics
Datasheet:
![MDS50-800](/images/manufacturer_photos/0/6/637/stmicroelectronics_tmb.jpg)
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
![MDS35-800](/images/manufacturer_photos/0/6/637/stmicroelectronics_tmb.jpg)
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
![E16N100](/images/manufacturer_photos/0/6/637/stmicroelectronics_tmb.jpg)
Part Number:
Description:
Search -----> STE16N100
Manufacturer:
STMicroelectronics
Datasheet:
![E53NA50](/images/manufacturer_photos/0/6/637/stmicroelectronics_tmb.jpg)
Part Number:
Description:
Search ---> STE53NA50
Manufacturer:
STMicroelectronics
Datasheet: