tmp1940cyaf TOSHIBA Semiconductor CORPORATION, tmp1940cyaf Datasheet - Page 377
tmp1940cyaf
Manufacturer Part Number
tmp1940cyaf
Description
32-bit Tx System Risc Tx19 Family
Manufacturer
TOSHIBA Semiconductor CORPORATION
Datasheet
1.TMP1940CYAF.pdf
(464 pages)
- Current page: 377 of 464
- Download datasheet (4Mb)
3.4
3.4.1
User Boot Mode (Single-Chip Mode)
situations where the flash memory is to be re-programmed via a bus other than serial I/O. User Boot mode is
one of the two submodes in Single-Chip mode; the other submode is Normal mode in which the CPU
executes the user application. To re-program the flash memory, the mode of operation must be switched
from Normal mode to User Boot mode. The user application code must include a mode judgment routine as
part of the reset procedure.
TMP1940FDBF. Additionally, the user must incorporate a programming algorithm into the user application
code that is to be executed after User Boot mode is entered.
programming algorithm must be placed and executed outside of the flash memory.
corruption.
memory is being erased or programmed.
stored within the TMP1940FDBF flash memory, and b) loaded from an external controller. For a detailed
description of the erase and program sequence, refer to Section 3.6, On-Board Programming and Erasure.
User Boot mode allows you to create a programming algorithm of your own. This mode supports
The user must define the conditions for mode switching, based on the logic states on I/O ports of the
It is not possible to read from the flash memory while it is being erased or programmed; therefore, the
Once re-programming is complete, it is recommended to protect relevant flash blocks from accidental
All interrupts including the nonmaskable (NMI) interrupt must be globally disabled while the flash
The pages that follow describe the general procedures for two cases where the programming routine is: a)
Method 1: Storing a Programming Routine in the Flash Memory
(1) Determine the conditions (e.g., pin states) required for the flash memory to enter User Boot mode
and the I/O bus to be used to transfer new program code. Create hardware and software
accordingly. Before installing the TMP1940FDBF on a printed circuit board, write the following
program routines into an arbitrary flash block using programming equipment.
Mode judgment routine: Code to determine whether or not to switch to User Boot mode
Programming routine:
Copy routine:
TMP1940FDBF
(a) Mode Judgment Routine
(b) Programming Routine
(c) Copy Routine
Flash Memory
[Reset Procedure]
Old Application
Program Code
TMP1940FDBF-19
Code to download new program code from a host controller and re-
program the flash memory
TMP1940FDBF flash memory to either the TMP1940FDBF on-chip
RAM or external memory device.
Code to copy the flash programming routine from the
Host Controller
I/O
RAM
New Application
Program Code
TMP1940FDBF
Related parts for tmp1940cyaf
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Toshiba Semiconductor [TOSHIBA IGBT Module Silicon N Channel IGBT]
Manufacturer:
TOSHIBA Semiconductor CORPORATION
Datasheet:
Part Number:
Description:
Toshiba Semiconductor [SILICON N CHANNEL 1GBT]
Manufacturer:
TOSHIBA Semiconductor CORPORATION
Datasheet:
Part Number:
Description:
Toshiba Semiconductor [GTR Module Silicon N Channel IGBT High Power Switching Applications Motor Control Applications]
Manufacturer:
TOSHIBA Semiconductor CORPORATION
Datasheet:
Part Number:
Description:
Toshiba Semiconductor [Power Module]
Manufacturer:
TOSHIBA Semiconductor CORPORATION
Datasheet:
Part Number:
Description:
TOSHIBA GTR MODULE SILICON NPN TRIPLE DIFFUSED TYPE
Manufacturer:
TOSHIBA Semiconductor CORPORATION
Datasheet:
Part Number:
Description:
TOSHIBA GTR Module Silicon N Channel IGBT
Manufacturer:
TOSHIBA Semiconductor CORPORATION
Datasheet:
Part Number:
Description:
TOSHIBA Intelligent Power Module Silicon N Channel IGBT
Manufacturer:
TOSHIBA Semiconductor CORPORATION
Datasheet:
Part Number:
Description:
TOSHIBA INTELLIGENT POWER MODULE SILICON N CHANNEL LGBT
Manufacturer:
TOSHIBA Semiconductor CORPORATION
Datasheet:
Part Number:
Description:
TOSHIBA IGBT Module Silicon N Channel IGBT
Manufacturer:
TOSHIBA Semiconductor CORPORATION
Datasheet:
Part Number:
Description:
TOSHIBA GTR MODULE SILICON N−CHANNEL IGBT
Manufacturer:
TOSHIBA Semiconductor CORPORATION
Datasheet:
Part Number:
Description:
TOSHIBA Intelligent Power Module Silicon N Channel IGBT
Manufacturer:
TOSHIBA Semiconductor CORPORATION
Datasheet:
Part Number:
Description:
TOSHIBA GTR Module Silicon N Channel IGBT
Manufacturer:
TOSHIBA Semiconductor CORPORATION
Datasheet:
Part Number:
Description:
TOSHIBA INTELLIGENT POWER MODULE
Manufacturer:
TOSHIBA Semiconductor CORPORATION
Datasheet:
Part Number:
Description:
TOSHIBA Intelligent Power Module Silicon N Channel IGBT
Manufacturer:
TOSHIBA Semiconductor CORPORATION
Datasheet:
Part Number:
Description:
TOSHIBA Intelligent Power Module Silicon N Channel IGBT
Manufacturer:
TOSHIBA Semiconductor CORPORATION
Datasheet: