S71PL032J SPANSION [SPANSION], S71PL032J Datasheet - Page 27

• Manufacturer Part Number: S71PL032J
• Description: STACKED MULTI CHIP PRODUCT FLASH MEMORY AND RAM
• Manufacturer: SPANSION [SPANSION]

General Description
August 12, 2004 S29PL127J_064J_032J_MCP_00_A3
Bank
D
A
B
C
Simultaneous Read/Write Operation with Zero Latency
Page Mode Features
Standard Flash Memory Features
16 Mbit (4 Kw x 8 and 32 Kw x 31)
16 Mbit (4 Kw x 8 and 32 Kw x 31)
48 Mbit (32 Kw x 96)
48 Mbit (32 Kw x 96)
The PL127J/PL064J/PL032J is a 128/128/64/32 Mbit, 3.0 volt-only Page Mode
and Simultaneous Read/Write Flash memory device organized as 8/8/4/2
Mwords. The devices are offered in the following packages:
The word-wide data (x16) appears on DQ15-DQ0. This device can be pro-
grammed in-system or in standard EPROM programmers. A 12.0 V V
required for write or erase operations.
The device offers fast page access times of 20 to 30 ns, with corresponding ran-
dom access times of 55 to 70 ns, respectively, allowing high speed
microprocessors to operate without wait states. To eliminate bus contention the
device has separate chip enable (CE#), write enable (WE#) and output enable
(OE#) controls.
The Simultaneous Read/Write architecture provides simultaneous operation
by dividing the memory space into 4 banks, which can be considered to be four
separate memory arrays as far as certain operations are concerned. The device
can improve overall system performance by allowing a host system to program
or erase in one bank, then immediately and simultaneously read from another
bank with zero latency (with two simultaneous operations operating at any one
time). This releases the system from waiting for the completion of a program or
erase operation, greatly improving system performance.
The device can be organized in both top and bottom sector configurations. The
banks are organized as follows:
The page size is 8 words. After initial page access is accomplished, the page mode
operation provides fast read access speed of random locations within that page.
The device requires a single 3.0 volt power supply (2.7 V to 3.6 V) for both
read and write functions. Internally generated and regulated voltages are pro-
vided for the program and erase operations.
The device is entirely command set compatible with the JEDEC 42.4 single-
power-supply Flash standard. Commands are written to the command regis-
ter using standard microprocessor write timing. Register contents serve as inputs
to an internal state-machine that controls the erase and programming circuitry.
Write cycles also internally latch addresses and data needed for the programming
PL127J Sectors
11mm x 8mm, 64-ball Fine-pitch BGA standalone (all)
9mm x 8mm, 80-ball Fine-pitch BGA standalone (PL127J)
8mm x 11.6mm, 64-ball Fine pitch BGA multi-chip compatible (PL127J)
A d v a n c e
S29PL127J/S29PL064J/S29PL032J for MCP
I n f o r m a t i o n
8 Mbit (4 Kw x 8 and 32 Kw x 15)
8 Mbit (4 Kw x 8 and 32 Kw x 15)
24 Mbit (32 Kw x 48)
24 Mbit (32 Kw x 48)
PL064J Sectors
4 Mbit (4 Kw x 8 and 32 Kw x 7)
4 Mbit (4 Kw x 8 and 32 Kw x 7)
12 Mbit (32 Kw x 24)
12 Mbit (32 Kw x 24)
PP
PL032J Sectors
is not
27