MC9S12P64VQK Freescale Semiconductor, MC9S12P64VQK Datasheet - Page 141

• Manufacturer Part Number: MC9S12P64VQK
• Description: 16-bit Microcontrollers - MCU 16 BIT 64K FLASH
• Manufacturer: Freescale Semiconductor

Specifications of MC9S12P64VQK

• Rohs: yes
• Core: S12
• Processor Series: MC9S12P
• Data Bus Width: 16 bit
• Maximum Clock Frequency: 64 MHz
• Program Memory Size: 64 KB
• Data Ram Size: 4 KB
• On-chip Adc: Yes
• Operating Supply Voltage: 5 V
• Operating Temperature Range: - 40 C to 105 C
• Package / Case: QFP-80
• Mounting Style: SMD/SMT
• Interface Type: I2C, SCI, SPI
• Program Memory Type: Flash

1. If enabled, ACK will occur when data is ready for transmission for all BDM READ commands and will occur after the write is
2. When the firmware command READ_NEXT or WRITE_NEXT is used to access the BDM address space the BDM resources
3. System stop disables the ACK function and ignored commands will not have an ACK-pulse (e.g., CPU in stop or wait mode).
5.4.5
Hardware and firmware BDM commands start with an 8-bit opcode followed by a 16-bit address and/or a
16-bit data word, depending on the command. All the read commands return 16 bits of data despite the
byte or word implication in the command name.
Freescale Semiconductor
READ_NEXT
READ_PC
READ_D
READ_X
READ_Y
READ_SP
WRITE_NEXT
WRITE_PC
WRITE_D
WRITE_X
WRITE_Y
WRITE_SP
GO
GO_UNTIL
TRACE1
TAGGO -> GO
complete for all BDM WRITE commands.
are accessed rather than user code. Writing BDM firmware is not possible.
The GO_UNTIL command will not get an Acknowledge if CPU executes the wait or stop instruction before the “UNTIL”
condition (BDM active again) is reached (see
Command
(3)
(2)
BDM Command Structure
(1)
8-bit reads return 16-bits of data, only one byte of which contains valid data.
If reading an even address, the valid data will appear in the MSB. If reading
an odd address, the valid data will appear in the LSB.
16-bit misaligned reads and writes are generally not allowed. If attempted
by BDM hardware command, the BDM ignores the least significant bit of
the address and assumes an even address from the remaining bits.
Opcode
(hex)
0C
62
63
64
65
66
67
42
43
44
45
46
47
08
10
18
16-bit data out Increment X index register by 2 (X = X + 2), then read word X points to.
16-bit data out Read program counter.
16-bit data out Read D accumulator.
16-bit data out Read X index register.
16-bit data out Read Y index register.
16-bit data out Read stack pointer.
16-bit data in
16-bit data in
16-bit data in
16-bit data in
16-bit data in
16-bit data in
Data
none
none
none
none
S12P-Family Reference Manual, Rev. 1.13
Table 5-5. Firmware Commands
Section 5.4.7, “Serial Interface Hardware Handshake Protocol”
Increment X index register by 2 (X = X + 2), then write word to location
pointed to by X.
Write program counter.
Write D accumulator.
Write X index register.
Write Y index register.
Write stack pointer.
Go to user program. If enabled, ACK will occur when leaving active
background mode.
Go to user program. If enabled, ACK will occur upon returning to active
background mode.
Execute one user instruction then return to active BDM. If enabled,
ACK will occur upon returning to active background mode.
(Previous enable tagging and go to user program.)
This command will be deprecated and should not be used anymore.
Opcode will be executed as a GO command.
Description
Background Debug Module (S12SBDMV1)
last note).
141