MC9S12P64VQK Freescale Semiconductor, MC9S12P64VQK Datasheet - Page 168

• Manufacturer Part Number: MC9S12P64VQK
• Description: 16-bit Microcontrollers - MCU 16 BIT 64K FLASH
• Manufacturer: Freescale Semiconductor

Specifications of MC9S12P64VQK

• Rohs: yes
• Core: S12
• Processor Series: MC9S12P
• Data Bus Width: 16 bit
• Maximum Clock Frequency: 64 MHz
• Program Memory Size: 64 KB
• Data Ram Size: 4 KB
• On-chip Adc: Yes
• Operating Supply Voltage: 5 V
• Operating Temperature Range: - 40 C to 105 C
• Package / Case: QFP-80
• Mounting Style: SMD/SMT
• Interface Type: I2C, SCI, SPI
• Program Memory Type: Flash

S12S Debug Module (S12SDBGV2)
6.3.2.7.4
Read: If COMRV[1:0] = 11
Write: Never
DBGMFR is visible at 0x0027 only with COMRV[1:0] = 11. It features 3 flag bits each mapped directly
to a channel. Should a match occur on the channel during the debug session, then the corresponding flag
is set and remains set until the next time the module is armed by writing to the ARM bit. Thus the contents
are retained after a debug session for evaluation purposes. These flags cannot be cleared by software, they
are cleared only when arming the module. A set flag does not inhibit the setting of other flags. Once a flag
is set, further comparator matches on the same channel in the same session have no affect on that flag.
6.3.2.8
Each comparator has a bank of registers that are visible through an 8-byte window in the DBG module
register address map. Comparator A consists of 8 register bytes (3 address bus compare registers, two data
bus compare registers, two data bus mask registers and a control register). Comparator B consists of four
register bytes (three address bus compare registers and a control register). Comparator C consists of four
register bytes (three address bus compare registers and a control register).
Each set of comparator registers can be accessed using the COMRV bits in the DBGC1 register.
Unimplemented registers (e.g. Comparator B data bus and data bus masking) read as zero and cannot be
written. The control register for comparator B differs from those of comparators A and C.
6.3.2.8.1
The contents of this register bits 7 and 6 differ depending upon which comparator registers are visible in
the 8-byte window of the DBG module register address map.
168
Address: 0x0027
0x002A
0x002B
0x002C
0x002D
0x002E
0x0028
0x0029
0x002F
Reset
W
R
Comparator Register Descriptions
0
0
7
Debug Match Flag Register (DBGMFR)
Debug Comparator Control Register (DBGXCTL)
DATA HIGH COMPARATOR
DATA LOW COMPARATOR
= Unimplemented or Reserved
ADDRESS MEDIUM
DATA HIGH MASK
DATA LOW MASK
ADDRESS HIGH
ADDRESS LOW
0
0
6
CONTROL
Figure 6-12. Debug Match Flag Register (DBGMFR)
Table 6-21. Comparator Register Layout
S12P-Family Reference Manual, Rev. 1.13
0
0
5
0
0
4
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
0
0
3
MC2
0
2
Comparators A,B and C
Comparators A,B and C
Comparators A,B and C
Comparators A,B and C
Comparator A only
Comparator A only
Comparator A only
Comparator A only
Freescale Semiconductor
MC1
0
1
MC0
0
0