TMPSNS-RTD1 Microchip Technology, TMPSNS-RTD1 Datasheet - Page 248

• Manufacturer Part Number: TMPSNS-RTD1
• Description: BOARD EVAL PT100 RTD TEMP SENSOR
• Manufacturer: Microchip Technology

Specifications of TMPSNS-RTD1

• Sensor Type: Temperature
• Interface: USB
• Embedded: Yes, MCU, 8-Bit
• Utilized Ic / Part: MCP3301, MCP6S26, PIC18F2550
• Processor To Be Evaluated: MCP6S26, MCP3301, MCP6024, MCP41010, PIC18F2550, TC1071, MCP6002
• Data Bus Width: 12 bit
• Interface Type: USB
• Lead Free Status / RoHS Status: Not applicable / Not applicable
• Voltage - Supply: -
• Sensitivity: -
• Sensing Range: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Not applicable / Not applicable

PIC18F2455/2550/4455/4550
REGISTER 20-3:
DS39632E-page 246
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
ABDOVF
R/W-0
ABDOVF: Auto-Baud Acquisition Rollover Status bit
1 = A BRG rollover has occurred during Auto-Baud Rate Detect mode (must be cleared in software)
0 = No BRG rollover has occurred
RCIDL: Receive Operation Idle Status bit
1 = Receive operation is Idle
0 = Receive operation is active
RXDTP: Received Data Polarity Select bit
Asynchronous mode:
1 = RX data is inverted
0 = RX data received is not inverted
Synchronous modes:
1 = Received Data (DT) is inverted. Idle state is a low level.
0 = No inversion of Data (DT). Idle state is a high level.
TXCKP: Clock and Data Polarity Select bit
Asynchronous mode:
1 = TX data is inverted
0 = TX data is not inverted
Synchronous modes:
1 = Clock (CK) is inverted. Idle state is a high level.
0 = No inversion of Clock (CK). Idle state is a low level.
BRG16: 16-Bit Baud Rate Register Enable bit
1 = 16-bit Baud Rate Generator – SPBRGH and SPBRG
0 = 8-bit Baud Rate Generator – SPBRG only (Compatible mode), SPBRGH value ignored
Unimplemented: Read as ‘0’
WUE: Wake-up Enable bit
Asynchronous mode:
1 = EUSART will continue to sample the RX pin – interrupt generated on falling edge; bit cleared in
0 = RX pin not monitored or rising edge detected
Synchronous mode:
Unused in this mode.
ABDEN: Auto-Baud Detect Enable bit
Asynchronous mode:
1 = Enable baud rate measurement on the next character. Requires reception of a Sync field (55h);
0 = Baud rate measurement disabled or completed
Synchronous mode:
Unused in this mode.
RCIDL
hardware on following rising edge
cleared in hardware upon completion.
R-1
BAUDCON: BAUD RATE CONTROL REGISTER
W = Writable bit
‘1’ = Bit is set
RXDTP
R/W-0
TXCKP
R/W-0
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
BRG16
R/W-0
U-0
—
© 2009 Microchip Technology Inc.
x = Bit is unknown
R/W-0
WUE
ABDEN
R/W-0
bit 0