MC68HC705C9ACFBE Freescale Semiconductor, MC68HC705C9ACFBE Datasheet - Page 75

• Manufacturer Part Number: MC68HC705C9ACFBE
• Description: IC MCU 8BIT 44-QFP
• Manufacturer: Freescale Semiconductor
• Series: HC05r

Specifications of MC68HC705C9ACFBE

• Core Processor: HC05
• Core Size: 8-Bit
• Speed: 2.1MHz
• Connectivity: SCI, SPI
• Peripherals: POR, WDT
• Number Of I /o: 24
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: OTP
• Ram Size: 352 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-QFP
• Processor Series: HC705C
• Core: HC05
• Data Bus Width: 8 bit
• Data Ram Size: 352 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 2.1 MHz
• Number Of Programmable I/os: 31
• Number Of Timers: 1
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit
• Package: 44PQFP
• Family Name: HC05
• Maximum Speed: 2.1 MHz
• Operating Supply Voltage: 3.3|5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Details

SPIE — Serial Peripheral Interrupt Enable Bit
SPE — Serial Peripheral System Enable Bit
DWOM — Port D Wire-OR Mode Option Bit
MSTR — Master Mode Select Bit
CPOL — Clock Polarity Bit
CPHA — Clock Phase Bit
SPR1 and SPR0 — SPI Clock Rate Selects
Freescale Semiconductor
This read/write bit enables SPI interrupts. Reset clears the SPIE bit.
This read/write bit enables the SPI. Reset clears the SPE bit.
This read/write bit disables the high side driver transistors on port D outputs so that port D outputs
become open-drain drivers. DWOM affects all seven port D pins together. This option is only available
when configured as a C9A.
This read/write bit selects master mode operation or slave mode operation. Reset clears the MSTR bit.
When the clock polarity bit is cleared and data is not being transferred, a steady state low value is
produced at the SCK pin of the master device. Conversely, if this bit is set, the SCK pin will idle high.
This bit is also used in conjunction with the clock phase control bit to produce the desired clock-data
relationship between master and slave. See
The clock phase bit, in conjunction with the CPOL bit, controls the clock-data relationship between
master and slave. The CPOL bit can be thought of as simply inserting an inverter in series with the
SCK line. The CPHA bit selects one of two fundamentally different clocking protocols. When
CPHA = 0, the shift clock is the OR of SCK with SS. As soon as SS goes low, the transaction begins
and the first edge on SCK invokes the first data sample. When CPHA=1, the SS pin may be thought
of as a simple output enable control. See
These read/write bits select one of four master mode serial clock rates, as shown in
have no effect in the slave mode.
1 = SPI interrupts enabled
0 = SPI interrupts disabled
1 = SPI system enabled
0 = SPI system disabled
1 = Port D outputs act as open-drain outputs.
0 = Port D outputs are normal CMOS outputs.
1 = Master mode
0 = Slave mode
$000A
Reset:
Read:
Write:
U = Undetermined
SPIE
Bit 7
0
MC68HC05C9A Advance Information Data Sheet, Rev. 4.1
Figure 10-4. SPI Control Register (SPCR)
SPE
6
0
DWOM
(C9A)
5
0
Figure
Figure
MSTR
4
0
10-1.
10-1.
CPOL
3
0
CPHA
2
1
SPR1
U
1
SPR0
Bit 0
Table
U
SPI Registers
10-1. They
75