MC9S12XDP512CAG Freescale Semiconductor, MC9S12XDP512CAG Datasheet - Page 1231

• Manufacturer Part Number: MC9S12XDP512CAG
• Description: IC MCU 512K FLASH 144-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12XDP512CAG

• Core Processor: HCS12X
• Core Size: 16-Bit
• Speed: 80MHz
• Connectivity: CAN, EBI/EMI, I²C, IrDA, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 119
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 5.5 V
• Data Converters: A/D 24x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 144-LQFP
• Processor Series: S12XD
• Core: HCS12
• Data Bus Width: 16 bit
• Data Ram Size: 32 KB
• Interface Type: CAN/I2C/SCI/SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 119
• Number Of Timers: 12
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: EVB9S12XDP512E
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 2 (24-ch x 10-bit)
• Cpu Family: HCS12
• Device Core Size: 16b
• Frequency (max): 40MHz
• Total Internal Ram Size: 32KB
• # I/os (max): 119
• Number Of Timers - General Purpose: 12
• Operating Supply Voltage (typ): 2.5/5V
• Operating Supply Voltage (max): 2.75/5.5V
• Operating Supply Voltage (min): 2.35/3.15V
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 144
• Package Type: LQFP
• For Use With: DEMO9S12XDT512E - BOARD DEMO FOR MC9S12XDT512EVB9S12XDP512E - BOARD DEMO FOR MC9S12XDP512
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

The meaning of the bits KEYEN[1:0] is shown in
“Unsecuring the MCU Using the Backdoor Key Access”
The meaning of the security bits SEC[1:0] is shown in
security is controlled by two bits. To put the device in unsecured mode, these bits must be programmed to
SEC[1:0] = ‘10’. All other combinations put the device in a secured mode. The recommended value to put
the device in secured state is the inverse of the unsecured state, i.e. SEC[1:0] = ‘01’.
30.1.4
By securing the device, unauthorized access to the EEPROM and Flash memory contents can be prevented.
However, it must be understood that the security of the EEPROM and Flash memory contents also depends
on the design of the application program. For example, if the application has the capability of downloading
code through a serial port and then executing that code (e.g. an application containing bootloader code),
then this capability could potentially be used to read the EEPROM and Flash memory contents even when
the microcontroller is in the secure state. In this example, the security of the application could be enhanced
by requiring a challenge/response authentication before any code can be downloaded.
Secured operation has the following effects on the microcontroller:
Freescale Semiconductor
Operation of the Secured Microcontroller
Please refer to the Flash block guide (FTX) for actual security configuration
(in section “Flash Module Security”).
Table 30-2. Backdoor Key Access Enable Bits
KEYEN[1:0]
SEC[1:0]
00
01
10
11
00
01
10
11
MC9S12XDP512 Data Sheet, Rev. 2.21
Table 30-3. Security Bits
NOTE
Table
Table
30-2. Please refer to
for more information.
Access Enabled
Security State
0 (unsecured)
Backdoor Key
30-3. For security reasons, the state of device
1 (secured)
1 (secured)
1 (secured)
0 (disabled)
0 (disabled)
0 (disabled)
1 (enabled)
Section 30.1.5.1,
Chapter 30 Security (S12X9SECV2)
1233