UPD70F3765GF-GAT-AX Renesas Electronics America, UPD70F3765GF-GAT-AX Datasheet - Page 1056

• Manufacturer Part Number: UPD70F3765GF-GAT-AX
• Description: MCU 32BIT V850ES/JX3-H 128-LQFP
• Manufacturer: Renesas Electronics America
• Series: V850ES/Jx3-Hr

Specifications of UPD70F3765GF-GAT-AX

• Core Processor: RISC
• Core Size: 32-Bit
• Speed: 48MHz
• Connectivity: CSI, EBI/EMI, I²C, UART/USART, USB
• Peripherals: DMA, LVD, PWM, WDT
• Number Of I /o: 96
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 40K x 8
• Voltage - Supply (vcc/vdd): 2.85 V ~ 3.6 V
• Data Converters: A/D 12x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

V850ES/JG3-H, V850ES/JH3-H
R01UH0042EJ0400 Rev.4.00
Sep 30, 2010
(g) SET_CONFIGURATION() request
(h) SET_FEATURE() request
If any of wValue, wIndex, or wLength is other than the values shown in Table 21-3, a STALL response is made
in the status stage.
• Default state:
• Addressed state: The CONF bit of the UF0MODS register and UF0CNF register are set to 1 and the device
• Configured state: The CONF bit of the UF0MODS register and UF0CNF register are set to 1 and the device
If the SET_CONFIGURATION() request has been correctly processed, the target bit of the UF0 SET request
register (UF0SET) is set to 1, and an interrupt is issued.
SET_CONFIGURATION() request has been completed even if the specified configuration value is the same as
the current configuration value. If the SET_CONFIGURATION() request has been correctly processed, the
data toggle of all endpoints is always initialized to DATA0 again (it is defined that the default status, Alternative
Setting 0, is set from when the SET_CONFIGURATION request is received to when the SET_INTERFACE
request is received).
A STALL response is made in the status stage if the SET_FEATURE() request is for a Feature that cannot be
set or does not exist, or if the target is an interface or an endpoint that does not exist. A STALL response is
also made if the wLength value is other than 0.
• Default state:
• Addressed state: The correct response is made when the SET_FEATURE() request has been received, only
• Configured state: The correct response is made when the SET_FEATURE() request has been received, only
When the SET_FEATURE() request has been correctly processed, the target bit of the UF0 SET request
register (UF0SET) and the EnHALT bit of the UF0 EPn status register L (UF0EnSL) are set to 1, and an
interrupt is issued (n = 0 to 4, 7).
The CONF bit of the UF0 mode status register (UF0MODS) and the UF0 configuration
register (UF0CNF) are set to 1 if the specified configuration value is 1 when the
SET_CONFIGURATION() request has been received. If the specified configuration value
is 0, the CONF bit of the UF0MODS register and UF0CNF register are cleared to 0. In
other words, the device skips the Addressed state and moves to the Configured state in
which it responds to the Default address.
enters the Configured state if the specified configuration value is 1 when the
SET_CONFIGURATION() request has been received. If the specified configuration value
is 0, the device remains in the Addressed state.
returns to the Addressed state if the specified configuration value is 0 when the
SET_CONFIGURATION() request has been received. If the specified configuration value
is 1, the device remains in the Configured state.
The correct response is made when the SET_FEATURE() request has been received, only
if the request is for a device or Endpoint0; otherwise a STALL response is made in the
status stage.
if the request is for a device or Endpoint0; otherwise a STALL response is made in the
status stage.
if the request is for a device or an endpoint that exists; otherwise a STALL response is
made in the status stage.
CHAPTER 21 USB FUNCTION CONTROLLER (USBF)
All Halt Features are cleared after the
Page 1056 of 1509