78M6612-IMR/F Maxim Integrated Products, 78M6612-IMR/F Datasheet - Page 49

• Manufacturer Part Number: 78M6612-IMR/F
• Description: IC POWER MEASUREMENT AC 68-QFN
• Manufacturer: Maxim Integrated Products

Specifications of 78M6612-IMR/F

• Mounting Style: SMD/SMT
• Package / Case: QFN-68
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

DS_6612_001
1.5.11 Hardware Watchdog Timer
Figure 14: Functions Defined by V1
Asserting ICE_E will also deactivate the WDT. This is the only method that will disable the WDT in
BROWNOUT mode.
In normal operation, the WDT is reset by periodically writing a one to the WDT_RST bit. The watchdog
timer is also reset when the internal signal WAKE=0 (see
1.5.12 Program Security
When enabled, the security feature limits the ICE to global Flash erase operations only. All other ICE
operations are blocked. This guarantees the security of the user’s MPU and CE program code. Security
preboot, the ICE can be enabled and is permitted to take control of the MPU.
SECURE, the security enable bit, is reset whenever the chip is reset. Hardware associated with the bit
permits only ones to be written to it. Thus, preboot code may set SECURE to enable the security feature
but may not reset it. Once SECURE is set, the preboot code is protected and no external read of program
code is possible,
Rev. 1.2
is enabled by MPU code that is executed in a 32 cycle preboot interval before the primary boot sequence
begins. Once security is enabled, the only way to disable it is to perform a global erase of the Flash,
followed by a chip reset.
The first 32 cycles of the MPU boot code are called the preboot phase because during this phase the ICE
is inhibited. A read-only status bit, PREBOOT, identifies these cycles to the MPU. Upon completion of
V3P3 - 10mV
400mV
V3P3 -
VBIAS
V3P3
0V
V1
operation,
enabled
Normal
Battery
WDT dis-
modes
WDT
abled
In addition to the basic watchdog timer included in the 80515 MPU,
an independent, robust, fixed-duration, watchdog timer (WDT) is
included in the device. It uses the RTC crystal oscillator as its time
base and must be refreshed by the MPU firmware at least every 1.5
seconds. When not refreshed on time the WDT overflows, and the
part is reset as if the RESET pin were pulled high, except that the
I/O RAM bits will be in the same state as after a wake-up from
SLEEP or LCD modes (see
list of I/O RAM bit states after RESET and wake-up). 4100 oscillator
cycles (or 125 ms) after the WDT overflow, the MPU will be launched
from program address 0x0000.
A status bit, WD_OVF, is set when WDT overflow occurs. This bit is
powered by the non-volatile supply and can be read by the MPU to
determine if the part is initializing after a WDT overflow event or after
a power-up. After it is read, MPU firmware must clear WD_OVF. The
WD_OVF bit is cleared by the RESET pin.
There is no internal digital state that deactivates the WDT. For
debug purposes, however, the WDT can be disabled by tying the V1
pin to V3P3 (see
power fault detection. Since there is no method in firmware to
disable the crystal oscillator or the WDT, it is guaranteed that
whatever state the part might find itself in, upon WDT overflow, the
part will be reset to a known state.
Figure
Section 2.5 Wake Up
36). Of course, this also deactivates V1
Section 4.3 I/O RAM Description
Behavior).
78M6612 Data Sheet
for a
49