PIC32MX575F512LT-80I/BG Microchip Technology, PIC32MX575F512LT-80I/BG Datasheet - Page 127

• Manufacturer Part Number: PIC32MX575F512LT-80I/BG
• Description: 512KB Flash, 64KB RAM, 80 MHz, USB, 1xCAN, 8 DMA 121 XBGA 10x10x1.20mm T/R
• Manufacturer: Microchip Technology
• Series: PIC® 32MXr

Specifications of PIC32MX575F512LT-80I/BG

• Core Processor: MIPS32® M4K™
• Core Size: 32-Bit
• Speed: 80MHz
• Connectivity: CAN, I²C, SPI, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 2.3 V ~ 3.6 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 121-TFBGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of I /o: -
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

11.0
The Universal Serial Bus (USB) module contains
analog and digital components to provide a USB 2.0
full-speed and low-speed embedded host, full-speed
device or OTG implementation with a minimum of
external components. This module in Host mode is
intended for use as an embedded host and therefore
does not implement a UHCI or OHCI controller.
The USB module consists of the clock generator, the
USB voltage comparators, the transceiver, the Serial
Interface Engine (SIE), a dedicated USB DMA control-
ler, pull-up and pull-down resistors, and the register
interface. A block diagram of the PIC32 USB OTG
module is presented in
© 2010 Microchip Technology Inc.
Note 1: This data sheet summarizes the features
2: Some registers and associated bits
USB ON-THE-GO (OTG)
of the PIC32MX5XX/6XX/7XX family of
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to Section 27. “USB On-
The-Go (OTG)” (DS61126) in the “PIC32
Family Reference Manual” , which is
available from the Microchip web site
(www.microchip.com/PIC32).
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization”
this data sheet for device-specific register
and bit information.
Figure
11-1.
in
The clock generator provides the 48 MHz clock
required for USB full-speed and low-speed communi-
cation. The voltage comparators monitor the voltage on
the V
transceiver provides the analog translation between
the USB bus and the digital logic. The SIE is a state
machine that transfers data to and from the endpoint
buffers and generates the hardware protocol for data
transfers. The USB DMA controller transfers data
between the data buffers in RAM and the SIE. The inte-
grated pull-up and pull-down resistors eliminate the
need for external signaling components. The register
interface
communicate with the module.
The PIC32 USB module includes the following
features:
• USB Full-speed support for host and device
• Low-speed host support
• USB OTG support
• Integrated signaling resistors
• Integrated analog comparators for V
• Integrated USB transceiver
• Transaction handshaking performed by hardware
• Endpoint buffering anywhere in system RAM
• Integrated DMA to access system RAM and Flash
PIC32MX5XX/6XX/7XX
monitoring
Note:
BUS
pin to determine the state of the bus. The
allows
The implementation and use of the USB
specifications, as well as other third party
specifications
require licensing; including, but not limited
to, USB Implementers Forum, Inc. (also
referred to as USB-IF). The user is fully
responsible for investigating and satisfy-
ing any applicable licensing obligations.
the
CPU
or
technologies,
to
DS61156F-page 127
configure
BUS
may
and