AD9898KCP-20 Analog Devices Inc, AD9898KCP-20 Datasheet - Page 16

• Manufacturer Part Number: AD9898KCP-20
• Description: IC CCD SIGNAL PROC/GEN 48-LFCSP
• Manufacturer: Analog Devices Inc
• Type: CCD Signal Processor, 10-Bitr

Specifications of AD9898KCP-20

• Rohs Status: RoHS non-compliant
• Input Type: Logic
• Output Type: Logic
• Interface: 3-Wire Serial
• Mounting Type: Surface Mount
• Package / Case: 48-LFCSP
• Analog Front End Type: CCD
• Analog Front End Category: Video
• Interface Type: Serial (3-Wire)
• Input Voltage Range: 0.5V
• Operating Supply Voltage (min): 2.7V
• Operating Supply Voltage (typ): 3V
• Operating Supply Voltage (max): 3.6V
• Resolution: 10b
• Number Of Adc's: 1
• Power Supply Type: Analog/Digital
• Operating Temp Range: -20C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LFCSP EP
• Number Of Channels: 3
• Current - Supply: -
• Lead Free Status / RoHS Status: Not Compliant

AD9898
SYSTEM OVERVIEW
Figure 5 shows the typical system block diagram for the AD9898.
The CCD output is processed by the AD9898’s AFE circuitry,
which consists of a CDS, VGA, black level clamp, and A/D
converter. The digitized pixel information is sent to the digital
image processor chip, which performs the postprocessing and
compression. To operate the CCD, all CCD timing parameters
are programmed into the AD9898 from the system micropro-
cessor, through the 3-wire serial interface. From the system
master clock, CLI, provided by the image processor or external
crystal, the AD9898 generates all the CCD’s horizontal and
vertical clocks and all internal AFE clocks. External synchroni-
zation is provided by a SYNC pulse from the microprocessor,
which will reset internal counters and resynchronize the VD and
HD outputs.
The AD9898 powers up in slave mode, in which the VD and
HD are provided externally from the image processor. In this
mode, all AD9898 timing will be synchronized with VD and
HD. The H-drivers for H1–H2 and RG are included in the
AD9898, allowing these clocks to be directly connected to the
CCD. H-drive voltage of up to 3.6 V is supported. An external
V-driver is required for the vertical transfer clocks, the sensor
gate pulses, and the substrate clock. The AD9898 also includes
programmable MSHUT and STROBE outputs, which may be
used to trigger mechanical shutter and strobe (flash) circuitry.
Figure 6 shows the horizontal and vertical counter dimensions
for the AD9898. All internal horizontal and vertical clocking is
programmed using these dimensions and is used to specify line
and pixel locations.
Figure 5. Typical System Block Diagram, Master Mode
CCD
STROBE
MSHUT
H1, H2, RG, VSUB
V-DRIVER
CCDIN
INTERFACE
SERIAL
V1–V4, VSG1, VSG2, SUBCK
AD9898
SYNC
P
OUTCONT
DOUT[9:0]
VGATE
DCLK1
HD, VD
CLI
FD
PROCESSING
DIGITAL
IMAGE
ASIC
–16–
CLI INPUT CLOCK DIVIDER
The AD9898 provides the capability of dividing the CLI input
clock using register CLKDIV (Addr 0xD5). The following
procedure must be followed to reset the AFE and digital circuits
when CLKDIV is reprogrammed back to 0 from CLKDIV = 1,
2, or 3. The DCLK1 output will become unstable if this proce-
dure is not followed:
Step 1: CLKDIV = 1, 2, or 3 (CLI divided by setting value)
Step 2: CLKDIV = 0 (CLI reprogrammed for no division)
Step 3: DIGSTBY = AFESTBY = 0
Step 4: DIGSTBY = AFESTBY = 1
GRAY CODE REGISTERS
Table V lists the AD9898 registers requiring gray code values.
Below is an example of applying a gray code number for
HDLEN using a line length of 1560 pixels:
(See Table XI note about HDLEN.)
The gray code value of 0x51E would be programmed in the
12-bit HDLEN register.
Figure 6. Horizontal and Vertical Counters
Register Name
HDLEN
CLPTOG1
CLPTOG2
HDLASTLEN
12-BIT HORIZONTALCOUNTER = 4096 PIXELS MAX
HDLEN = (1560 – 4) = 1556
Table V. Gray Code Registers
MAXIMUM FIELD DIMENSIONS
1556
10
= 0x51E
Register Type
System_Reg(12)
System_Reg(15)
System_Reg(15 and 16)
Mode_Reg(1)
10
REV. 0