ATtiny28L Atmel Corporation, ATtiny28L Datasheet - Page 19

no-image

ATtiny28L

Manufacturer Part Number
ATtiny28L
Description
Manufacturer
Atmel Corporation
Datasheets

Specifications of ATtiny28L

Flash (kbytes)
2 Kbytes
Pin Count
28
Max. Operating Frequency
4 MHz
Cpu
8-bit AVR
Hardware Qtouch Acquisition
No
Max I/o Pins
11
Ext Interrupts
10
Usb Speed
No
Usb Interface
No
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
0.03
Self Program Memory
NO
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8 to 5.5
Operating Voltage (vcc)
1.8 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
1
32khz Rtc
No
Calibrated Rc Oscillator
Yes

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATtiny28L-1AC
Manufacturer:
ATMEL
Quantity:
1 187
Part Number:
ATtiny28L-1AI
Manufacturer:
ATMEL
Quantity:
2 840
Part Number:
ATtiny28L-4AC
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATtiny28L-4AC
Manufacturer:
ATMEL
Quantity:
31 007
Part Number:
ATtiny28L-4AI
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATtiny28L-4AI
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATtiny28L-4AU
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATtiny28L-4AUR
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATtiny28L-4AUR
Manufacturer:
ATMEL
Quantity:
4 759
Part Number:
ATtiny28L-4MU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATtiny28L-4PC
Manufacturer:
EPCOS
Quantity:
3 000
Part Number:
ATtiny28L-4PC
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
ATtiny28L-4PI
Quantity:
479
Part Number:
ATtiny28L-4PU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Register Description
MCU Control and Status
Register – MCUCS
1062F–AVR–07/06
The MCU Control and Status Register contains control and status bits for general MCU
functions.
• Bit 7 – PLUPB: Pull-up Enable Port B
When the PLUPB bit is set (one), pull-up resistors are enabled on all Port B input pins.
When PLUPB is cleared, the pull-ups are disabled. If any of the special functions of Port
B is enabled, the corresponding pull-up(s) is disabled, independent of the value of
PLUPB.
• Bit 6 – Res: Reserved Bit
This bit is a reserved bit in the ATtiny28 and always reads as zero.
• Bit 5 – SE: Sleep Enable
The SE bit must be set (one) to make the MCU enter the sleep mode when the SLEEP
instruction is executed. To avoid the MCU entering the sleep mode unless it is the pro-
grammer’s purpose, it is recommended to set the Sleep Enable SE bit just before the
execution of the SLEEP instruction.
• Bit 4 – SM: Sleep Mode
This bit selects between the two available sleep modes. When SM is cleared (zero), Idle
Mode is selected as sleep mode. When SM is set (one), Power-down mode is selected
as sleep mode. For details, refer to “Sleep Modes” below.
• Bit 3 – WDRF: Watchdog Reset Flag
This bit is set if a Watchdog reset occurs. The bit is cleared by a Power-on Reset, or by
writing a logical “0” to the flag.
• Bit 2 – Res: Reserved Bit
This bit is a reserved bit in the ATtiny28 and always reads as zero.
• Bit 1 – EXTRF: External Reset Flag
This bit is set if an external reset occurs. The bit is cleared by a Power-on Reset, or by
writing a logical “0” to the flag.
• Bit 0 – PORF: Power-on Reset Flag
This bit is set if a Power-on Reset occurs. The bit is cleared by writing a logical “0” to the
flag.
To make use of the reset flags to identify a reset condition, the user should read and
then clear the flag bits in MCUCS as early as possible in the program. If the register is
cleared before another reset occurs, the source of the reset can be found by examining
the reset flags.
Bit
$07
Read/Write
Initial Value
PLUPB
R/W
7
0
R
6
0
R/W
SE
5
0
R/W
SM
4
0
See Bit
WDRF
Desc.
R/W
3
R
2
0
ATtiny28L/V
EXTRF
See Bit Description
R/W
1
PORF
R/W
0
MCUCS
19

Related parts for ATtiny28L