MCF5272VM66 Freescale Semiconductor, MCF5272VM66 Datasheet - Page 379

• Manufacturer Part Number: MCF5272VM66
• Description: IC MPU 66MHZ COLDFIRE 196-MAPBGA
• Manufacturer: Freescale Semiconductor
• Series: MCF527xr

Specifications of MCF5272VM66

• Core Processor: Coldfire V2
• Core Size: 32-Bit
• Speed: 66MHz
• Connectivity: EBI/EMI, Ethernet, I²C, SPI, UART/USART, USB
• Peripherals: DMA, WDT
• Number Of I /o: 32
• Program Memory Size: 16KB (4K x 32)
• Program Memory Type: ROM
• Ram Size: 1K x 32
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 196-MAPBGA
• Family Name: MCF5xxx
• Device Core: ColdFire
• Device Core Size: 32b
• Frequency (max): 66MHz
• Instruction Set Architecture: RISC
• Supply Voltage 1 (typ): 3.3V
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 196
• Package Type: MA-BGA
• Cpu Speed: 66MHz
• Embedded Interface Type: UART, QSPI, USB, TDM
• Digital Ic Case Style: BGA
• No. Of Pins: 196
• Supply Voltage Range: 3V To 3.6V
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Compliant

An internal interrupt request signal (IRQ) is provided to notify the interrupt controller of an interrupt
condition. The output is the logical NOR of unmasked UISRn bits. The interrupt levels of the UART
modules are programmed in SIM register ICR2. See
Table 16-15
Figure 16-22
16.5
This section describes operation of the clock source generator, transmitter, and receiver.
16.5.1
CLKIN serves as the basic timing reference for the clock source generator logic, which consists of a clock
generator and a programmable 16+4-bit divider (UDU, UDL, UFPD) dedicated to the UART. The clock
generator cannot produce standard baud rates if CLKIN is used, so the 16-bit divider should be used.
Freescale Semiconductor
Transmitter Serial
Data Output
(URT_TxD)
Receiver Serial Data
Input (URT_RxD)
Clear-to-Send
(URT_CTS)
Request-to-Send
(URT_RTS)
Clock (URT_CLK)
Signal
Operation
Transmitter/Receiver Clock Source
briefly describes the UART module signals.
shows a signal configuration for a UART/RS-232 interface.
The terms ‘assertion’ and ‘negation’ are used to avoid confusion between
active-low and active-high signals. ‘Asserted’ indicates that a signal is
active, independent of the voltage level; ‘negated’ indicates that a signal is
inactive.
URT_TxD is held high (mark condition) when the transmitter is disabled, idle, or operating in the local
loop-back mode. Data is shifted out on URT_TxD on the falling edge of the clock source, with the least
significant bit (lsb) sent first.
Data received on URT_RxD is sampled on the rising edge of the clock source, with the lsb received first.
This input can generate an interrupt on a change of state.
This output can be programmed to be negated or asserted automatically by either the receiver or the
transmitter. It can control serial data flow when connected to a transmitter’s CTS.
The UART’s external clock source. It can be used in 1x or 16x mode. When both the transmitter and
receiver use the timer as the clock source (UCR = 0xDD), the 16x clock is driven out on UARTCLK. If
either the transmitter or receiver use an external clock (1x or 16x), URT_CLK is an input.
MCF5272 ColdFire
URT_CTS
URT_RTS
URT_RxD
URT_TxD
Figure 16-22. UART/RS-232 Interface
UART
Table 16-15. UART Module Signals
®
Integrated Microprocessor User’s Manual, Rev. 3
NOTE
Section 7.2, “Interrupt Controller
Description
RS-232 Transceiver
DI2
DO2
DI1
DO1
Registers.”
UART Modules
16-19