A000047 Arduino, A000047 Datasheet - Page 43
A000047
Manufacturer Part Number
A000047
Description
MCU, MPU & DSP Development Tools Mega2560
Manufacturer
Arduino
Series
-r
Type
MCUr
Specifications of A000047
Processor To Be Evaluated
ATmega2560
Interface Type
USB, I2C, SPI
Dimensions
4 in x 2.1 in
Operating Supply Voltage
5 V
Contents
Board
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With/related Products
ATmega2560
- Current page: 43 of 444
- Download datasheet (10Mb)
2549M–AVR–09/10
C1 and C2 should always be equal for both crystals and resonators. The optimal value of the
capacitors depends on the crystal or resonator in use, the amount of stray capacitance, and the
electromagnetic noise of the environment. Some initial guidelines for choosing capacitors for
use with crystals are given in
the manufacturer should be used.
Figure 9-2.
The Low Power Oscillator can operate in three different modes, each optimized for a specific fre-
quency range. The operating mode is selected by the fuses CKSEL3:1 as shown in
Table 9-3.
Notes:
The CKSEL0 Fuse together with the SUT1:0 Fuses select the start-up times as shown in
9-4.
Table 9-4.
Ceramic resonator, slowly
Ceramic resonator, BOD
Ceramic resonator, fast
Oscillator Source /
Power Conditions
Frequency Range (MHz)
rising power
rising power
1. This is the recommended CKSEL settings for the different frequency ranges.
2. This option should not be used with crystals, only with ceramic resonators.
3. If 8 MHz frequency exceeds the specification of the device (depends on V
4. Max frequency when using ceramic oscillator is 10 MHz.
enabled
Fuse can be programmed in order to divide the internal frequency by 8. It must be ensured
that the resulting divided clock meets the frequency specification of the device.
8.0 - 16.0
0.4 - 0.9
0.9 - 3.0
3.0 - 8.0
Crystal Oscillator Connections
Low Power Crystal Oscillator Operating Modes
Start-up Times for the Low Power Crystal Oscillator Clock Selection
(4)
Start-up Time from
Table
Power-down and
ATmega640/1280/1281/2560/2561
Power-save
258 CK
258 CK
1K CK
9-3. For ceramic resonators, the capacitor values given by
C2
C1
CKSEL3:1
100
101
110
111
(2)
(1)
Additional Delay
14CK + 4.1 ms
14CK + 65 ms
Recommended Range for Capacitors C1
(V
from Reset
XTAL2
XTAL1
GND
CC
14CK
= 5.0V)
(3)
(2)
(1)
(1)
and C2 (pF)
12 - 22
12 - 22
12 - 22
–
CKSEL0
CC
0
0
0
), the CKDIV8
Table
SUT1:0
00
01
10
9-3.
Table
43
Related parts for A000047
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Daughter Cards & OEM Boards ARDUINO UNO PROTO PCB REV 3
Manufacturer:
Arduino
Part Number:
Description:
Daughter Cards & OEM Boards ARDUINO SHIELD PROTO KIT REV 3
Manufacturer:
Arduino
Part Number:
Description:
Daughter Cards & OEM Boards ARDUINO MEGA PROTO KIT REV 3
Manufacturer:
Arduino
Part Number:
Description:
Daughter Cards & OEM Boards ARDUINO MEGA PROTO PCB REV 3
Manufacturer:
Arduino
Part Number:
Description:
Development Boards & Kits - AVR ARDUINO STARTER KIT W/ UNO REV3
Manufacturer:
Arduino
Part Number:
Description:
RF Development Tools ARDUINO SHIELD WIRELESS PROTO
Manufacturer:
Arduino
Datasheet:
Part Number:
Description:
RF Development Tools ARDUINO SHIELD WIRELESS WITH SD
Manufacturer:
Arduino
Datasheet:
Part Number:
Description:
Development Software Getting started w/Arduino
Manufacturer:
Arduino
Part Number:
Description:
Ethernet Modules & Development Tools Ethernet Shield for Arduino
Manufacturer:
Arduino
Part Number:
Description:
MCU, MPU & DSP Development Tools LilyPad Arduino Main Board
Manufacturer:
Arduino
Part Number:
Description:
ARDUINO NANO Board
Manufacturer:
Arduino
Datasheet:
Part Number:
Description:
Ethernet Modules & Development Tools ETHERNET SHEILD PoE FOR ARDUINO
Manufacturer:
Arduino
Datasheet:
Part Number:
Description:
ATMEGA328 MCU IC W/ Arduino UNO Bootloader
Manufacturer:
Arduino
Datasheet:
Part Number:
Description:
Memory Cards MICRO SD CARD 1GB WITH SD ADAPTER
Manufacturer:
Arduino