DS33R41 Maxim Integrated Products, DS33R41 Datasheet - Page 169
DS33R41
Manufacturer Part Number
DS33R41
Description
Network Controller & Processor ICs Inverse-Multiplexing Ethernet Mapper wit
Manufacturer
Maxim Integrated Products
Datasheet
1.DS33R41.pdf
(335 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DS33R41+
Manufacturer:
Maxim Integrated Products
Quantity:
135
Company:
Part Number:
DS33R41+
Manufacturer:
Maxim
Quantity:
84
- Current page: 169 of 335
- Download datasheet (2Mb)
Register Name:
Register Description:
Register Address:
Bit #
Name
Default
Bit 0: Queue Loopback Enable (QLP). If this bit is set to 1, data from the Ethernet Interface receive queue is
looped back to the transmit queue. Buffered data from the serial interface will remain until the loopback is removed.
Register Name:
Register Description:
Register Address:
Bit #
Name
Default
Bit 3: CRCS. If this bit is zero (default), the received MAC or Ethernet Frame CRC is stripped before the data is
encapsulated and transmitted on the serial interface. Data received from the serial interface is decapsulated, a
CRC is recalculated and appended to the packet for transmission to the Ethernet interface. If this bit is set to 1, the
CRC is not stripped from received packets prior to encapsulation and transmission to the serial interface, and data
received from the serial interface is decapsulated directly. No CRC recalculation is performed on data received
from the serial interface. Note that the maximum packet size supported by the Ethernet interface is still 2016 (this
includes the 4 bytes of CRC).
Bit 2: H10S This bit controls the 10/100 selection for RMII and DCE Mode. When in RMII mode, setting this bit to
1 will cause the MAC will operate at 100 Mbps and setting this bit to zero will cause the MAC to operate at 10
Mbps. When in DCE mode, the bit function is inverted – setting this bit to 1 will cause the MAC to operate at 10
Mbps. In DTE and MII mode, the MAC determines the data rate from the incoming TX_CLK and RX_CLK.
Bit 1: Automatic Flow Control Enable (ATFLOW). If this bit is set to 1, automatic flow control is enabled based
on the connection receive queue size and high watermarks. Pause frames are sent automatically in full duplex
mode. The pause time must be programmed through SU.MACFCR. The jam sequence will not be sent
automatically in half duplex mode unless the JAME bit is set. This bit is applicable only in software mode.
Bit 0: Jam Enable (JAME.) If this bit is set to 1, a Jam sequence is sent for a duration of 4 bytes. This function is
only valid in half duplex mode, and will only function if Automatic Flow Control is disabled. Note that if the receive
queue size is less than receive high threshold, setting a JAME will JAM one received frame. If JAME is set and the
receiver queue size is higher than the high threshold, all received frames are jammed until the queue empties
below the threshold.
Note that
control and 100/10-speed selection.
SU.GCR
—
—
7
0
7
0
is only valid in the software mode. In hardware mode, pins are used to control Automatic flow
—
—
6
0
6
0
SU.LPBK
Ethernet Interface Loopback Control Register
14Fh
SU.GCR
Ethernet Interface General Control Register
150h
—
—
5
0
5
0
169 of 335
—
—
0
0
4
4
CRCS
—
3
0
3
0
H10S
—
2
0
2
0
ATFLOW
—
1
0
1
1
JAME
QLP
0
0
0
0
Related parts for DS33R41
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN 16/A°/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I°/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I°/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
EVALUATION KIT/2.4GHZ TO 2.5GHZ 802.11G/B RF TRANSCEIVER WITH INTEGRATED PA
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN/E/DUAL PCIE/SATA HIGH SPEED SWITCH WITH INTEGRATED BIAS RESISTOR
Manufacturer:
Maxim Integrated Products
Datasheet: