NH82801FBM S L89K Intel, NH82801FBM S L89K Datasheet - Page 176

• Manufacturer Part Number: NH82801FBM S L89K
• Manufacturer: Intel

Specifications of NH82801FBM S L89K

• Lead Free Status / RoHS Status: Compliant

Functional Description
176
The following rules/steps apply if the system is in a G0 state and the policy is for the ICH6 to
reboot the system after a hardware lockup:
The following rules/steps apply if the system is in a G0 state and the policy is for the ICH6 to not
reboot the system after a hardware lockup.
10. After step 8 (reset attempt), if the reset is unsuccessful, the ICH6 continues sending a message
1. On detecting the lockup, the SECOND_TO_STS bit is set. The ICH6 may send up to 1 Event
2. If the reboot at step 1 is successful then the BIOS should clear the SECOND_TO_STS bit.
3. If the reboot attempt in step 1 is not successful, the timer will timeout a third time. At this point
4. After step 3 (unsuccessful reboot after third timeout), if the user does a Power Button
5. After step 4 (power button override after unsuccessful reboot) if the user presses the Power
6. If step 5 (power button press) is successful in waking the system, the ICH6 continues sending
7. If step 5 (power button press) is unsuccessful in waking the system, the ICH6 continues
8. After step 3 (unsuccessful reboot after third timeout), if a reset is attempted (using a button
9. After step 8 (reset attempt) if the reset is successful, the BIOS is run. The ICH6 continues
1. On detecting the lockup the SECOND_TO_STS bit is set. The ICH6 sends a message with the
2. After step 1, the ICH6 sends a message every heartbeat period until some external intervention
3. Rules/steps 4–10 apply if no user intervention (resets, power button presses, SMBus reset
4. After step 3 (third timeout), if the user does a Power Button Override, the system goes to an S5
message to the LAN controller. The ICH6 then attempts to reboot the processor.
This prevents any further Heartbeats from being sent. The BIOS may then perform addition
recovery/boot steps. (See note 2, below.)
the system has locked up and was unsuccessful in rebooting. The ICH6 does not attempt to
automatically reboot again. The ICH6 starts sending a message every heartbeat period
(30–32 seconds). The heartbeats continue until some external intervention occurs (reset, power
failure, etc.).
Override, the system goes to an S5 state. The ICH6 continues sending the messages every
heartbeat period.
Button again, the system should wake to an S0 state and the processor should start executing
the BIOS.
messages every heartbeat period until the BIOS clears the SECOND_TO_STS bit. (See note 2)
sending a message every heartbeat period. The ICH6 does not attempt to automatically reboot
again. The ICH6 starts sending a message every heartbeat period (30–32 seconds). The
heartbeats continue until some external intervention occurs (reset, power failure, etc.).
(See note 3)
that pulses PWROK low or via the message on the SMBus slave I/F), the ICH6 attempts to
reset the system.
sending a message every heartbeat period until the BIOS clears the SECOND_TO_STS bit.
(See note 2)
every heartbeat period. The ICH6 does not attempt to reboot the system again without external
intervention. (See note 3)
Watchdog (WD) Event status bit set (and any other bits that must also be set). This message is
sent as soon as the lockup is detected, and is sent with the next (incremented) sequence
number.
occurs.
messages) occur after a third timeout of the watchdog timer. If the intervention occurs before
the third timeout, then jump to rule/step 11.
state. The ICH6 continues sending heartbeats at this point.
Intel
®
I/O Controller Hub 6 (ICH6) Family Datasheet