SAM3A8C Atmel Corporation, SAM3A8C Datasheet - Page 1452
SAM3A8C
Manufacturer Part Number
SAM3A8C
Description
Manufacturer
Atmel Corporation
- Current page: 1452 of 1465
- Download datasheet (26Mb)
48.2.4
48.2.4.1
48.2.4.2
48.2.4.3
48.2.5
48.2.5.1
1452
SAM3X/A
Analog to Digital Converter (ADC)
JTAG Boundary
ADC: First conversion after sleep
ADC: Last Conversion Error
ADC: Wrong First Conversions
JJTAG Boundary: PC0/ERASE
In sleep mode, first converted data incorrect after Wakeup.
One or more channels must be converted using sleep mode, a dummy channel as first channel
of the series can be used.
In sleep mode, last converted data incorrect before Shutdown.
One or more channels must be converted using sleep mode, a dummy channel as first channel
of the series can be used.
The first conversions done by the ADC may be erroneous if the maximum gain (x4 in single
ended or x2 in differential mode) is not used. The issue appears after the power-up or if a con-
version has not been occured for 1 minute.
Three workarounds are possible :
1) Perform 16 dummy conversions on one channel (whatever conditions used in term of setup of
gain, single/differential, offset, and channel selected). The next conversions will be correct for
any channels and any settings. Note that these dummy conversions need to be performed if no
conversion has occured for 1 minute or for a new chip start-up.
2) Perform a dummy conversion on a single ended channel on which an external voltage of
ADVREF/2 (+/-10%) is applied. And use the following conditions for this conversion: gain at 4,
offset set at 1. The next conversions will be correct for any channels and any settings. Note that
this dummy conversion needs to be performed if no conversion has occured for 1 minute or for a
new chip start-up.
3) Perform a dummy conversion on a differential channel on which the two inputs are connected
together and connected to any voltage (from 0 to ADVREF). And use the following conditions for
this conversion: gain at 4, offset set at 1. The next conversions will be correct for any channels
and any settings. Note that this dummy conversion needs to be performed if no conversion has
occured for 1 minute or for a new chip start-up.
In JTAG Boundary Scan mode, the PIO PC0 which is by default the ERASE pin may erase the
Flash content if the pin is set to high level.
Do not use PC0/ERASE (or tie to 0) or set PC0/ERASE at high level during a time lower than
150 ms in Boundary JTAG Scan mode or program the Flash after using this mode.
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
11057A–ATARM–17-Feb-12
Related parts for SAM3A8C
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
AT91SAM ARM-based Flash MCU
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: