SAM3A8C Atmel Corporation, SAM3A8C Datasheet - Page 304
SAM3A8C
Manufacturer Part Number
SAM3A8C
Description
Manufacturer
Atmel Corporation
- Current page: 304 of 1465
- Download datasheet (26Mb)
Figure 19-6. Example of Partial Page Programming
19.4.3.3
19.4.3.4
304
304
X words
X words
X words
X words
SAM3X/A
SAM3X/A
Erase Commands
Lock Bit Protection
So Page Y erased
Erase All Flash
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
32-bit wide
Step 1.
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
...
...
...
...
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
Two errors can be detected in the EEFC_FSR register after a programming sequence:
By using the WP command, a page can be programmed in several steps if it has been erased
before (see
The Partial Programming mode works only with 128-bit (or higher) boundaries. It cannot be used
with boundaries lower than 128 bits (8, 16 or 32-bit for example).
Erase commands are allowed only on unlocked regions.
The erase sequence is:
Two errors can be detected in the EEFC_FSR register after a programming sequence:
Lock bits are associated with several pages in the embedded Flash memory plane. This defines
lock regions in the embedded Flash memory plane. They prevent writing/erasing protected
pages.
• a Command Error: a bad keyword has been written in the EEFC_FCR register.
• a Lock Error: the page to be programmed belongs to a locked region. A command must be
• Erase starts as soon as one of the erase commands and the FARG field are written in the
• When the programming completes, the FRDY bit in the Flash Programming Status Register
• a Command Error: a bad keyword has been written in the EEFC_FCR register.
• a Lock Error: at least one page to be erased belongs to a locked region. The erase command
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
previously run to unlock the corresponding region.
Flash Command Register.
(EEFC_FSR) rises. If an interrupt has been enabled by setting the FRDY bit in EEFC_FMR,
the interrupt line of the NVIC is activated.
has been refused, no page has been erased. A command must be run previously to unlock
the corresponding region.
Figure
Programming of the second part of Page Y
19-6).
FF
FF
FF
CA FE
CA FE
CA FE
FF
FF
FF
FF
FF
FF
32-bit wide
FF
FF
FF
Step 2.
FF
FF
FF
FF
FF
FF
...
...
...
...
FF
FF
FF
CA
CA
CA
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FF
FE
FE
FE
Programming of the third part of Page Y
FF
FF
FF
CA FE
CA FE
CA FE
DE CA
DE CA
DE CA
FF
FF
FF
32-bit wide
FF
FF
FF
FF
FF
FF
Step 3.
...
...
...
...
11057A–ATARM–17-Feb-12
11057A–ATARM–17-Feb-12
FF
FF
FF
CA
CA
CA
DE CA
DE CA
DE CA
FF
FF
FF
FF
FF
FF
FE
FE
FE
FF
FF
FF
Related parts for SAM3A8C
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
AT91SAM ARM-based Flash MCU
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: