ST72361AR9-Auto STMicroelectronics, ST72361AR9-Auto Datasheet - Page 228
ST72361AR9-Auto
Manufacturer Part Number
ST72361AR9-Auto
Description
8-bit MCU for automotive with K Flash, 10-bit ADC, 5 Timers, SPI, 2x LINSCI
Manufacturer
STMicroelectronics
Datasheet
1.ST72361AR9-AUTO.pdf
(279 pages)
Specifications of ST72361AR9-Auto
Hdflash Endurance
100 cycles, data retention 20 years at 55 °C
5 Power Saving Modes
halt, auto wake up from halt, active halt, wait and slow
- Current page: 228 of 279
- Download datasheet (3Mb)
Electrical characteristics
19.2
19.2.1
228/279
Figure 96. Pin input voltage
Absolute maximum ratings
Stresses above those listed as “absolute maximum ratings” may cause permanent damage
to the device. This is a stress rating only and functional operation of the device under these
conditions is not implied. Exposure to maximum rating conditions for extended periods may
affect device reliability.
Voltage characteristics
1. Directly connecting the RESET and I/O pins to V
2. I
|V
internal reset is generated or an unexpected change of the I/O configuration occurs (for example, due to a
corrupted program counter). To guarantee safe operation, this connection has to be done through a pull-up
or pull-down resistor (typical: 4.7k
way to V
cannot be respected, the injection current must be limited externally to the I
injection is induced by V
pads, there is no positive injection current, and the corresponding V
INJ(PIN)
DDx
|V
V
V
V
V
SSA
Symbol
ESD(HBM)
DD
PP
ESD(MM)
| and |V
V
- V
- V
- V
must never be exceeded. This is implicitly insured if V
IN
DD
SS
SS
SSx
or V
SSx
|
SS
| Variations between different digital power pins
according to their reset configuration.
Supply voltage
Programming Voltage
Input voltage on any pin
Variations between digital and analog ground
pins
Electro-static discharge voltage (Human Body
Model)
Electro-static discharge voltage (Machine
Model)
IN
>V
DD
while a negative injection is induced by V
Doc ID 12468 Rev 3
for RESET, 10k
Ratings
V
IN
DD
(1)(2)
or V
for I/Os). Unused I/O pins must be tied in the same
SS
could damage the device if an unintentional
ST7 PIN
IN
maximum is respected. If V
IN
maximum must always be respected.
IN
INJ(PIN)
< V
V
Absolute maximum ratings
SS
SS
Maximum value
. For true open-drain
(electrical sensitivity)
- 0.3 to V
value. A positive
see
Section 20.8.3:
6.5
ST72361xx-Auto
13
50
50
IN
DD
maximum
+ 0.3
Unit
mV
V
Related parts for ST72361AR9-Auto
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
TURBOSWITCH ULTRA-FAST HIGH VOLTAGE DIODE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search -----> STE16N100
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search ---> STE53NA50
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN Transistor Power Module
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet: